Home › Brake › BRAKE (FRONT) › FRONT DISC BRAKE PAD(for 15 inch Front Disc Brake 2WD)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193994 FRONT DISC BRAKE PAD(for 15 inch Front Disc Brake 2WD) A

BRAKE (FRONT)  FRONT DISC BRAKE PAD(for 15 inch Front Disc Brake 2WD)  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



NOTICE:

After replacing the disc brake pads, the clearance between the disc brake pads and front discs becomes larger and the brake pedal feel becomes softer. Therefore, after replacing the disc brake pads, depress the brake pedal several times and check the clearance and brake pedal feel.


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 47750 3.REMOVE DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321893C02
1.313,2.292 0.865,2.01 0.865,2.01 0.677,2.01 false 1.958,2.563 1.667,2.781 1.667,2.781 1.542,2.781 false 0.458,1.927 0.615,2.125 0.156,0.198 10 false *a 1.365,2.698 1.563,2.885 0.198,0.188 10 false *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and remove the 2 bolts.


b.

Disconnect the disc brake cylinder assembly LH from the front disc brake cylinder mounting LH.


Hide 04465 4.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the front disc brake cylinder mounting LH.


Hide 04945 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims and 2 No. 2 anti-squeal shims from each pad.


Hide 6.REMOVE PAD WEAR INDICATOR PLATE

a.
C306284

Using a screwdriver, remove the pad wear indicator plates from the front disc brake pads as shown in the illustration.


Hide 7.INSTALL PAD WEAR INDICATOR PLATE

a.

Install a new pad wear indicator plate to the inner lower side of the front disc brake pad.

NOTICE:

Install the pad wear indicator plate in the correct position and direction.



Hide 04945 8.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C321892C01
0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 0.208,2.531 0.521,2.688 0.313,0.156 10 false *b
*a Inner Pad
*b Outer Pad
V100145

Area for disc brake grease application


Apply disc brake grease to the inside of the 2 No. 1 anti-squeal shims as shown in the illustration.

NOTICE:
·

When replacing worn pads, the No. 1 anti-squeal shims must be replaced together with the pads.

·

Apply disc brake grease to the area that contacts the No. 1 anti-squeal shims.

·

Disc brake grease can come out slightly from the area where the No. 1 anti-squeal shims are installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




b.
C321890C01
1.292,1.135 1.292,0.854 1.292,0.854 2.229,0.854 false 1.938,1.438 1.938,0.854 false 0.875,1.563 0.875,2.094 0.875,2.094 0.615,2.094 false 2.594,2.417 2.594,2.833 2.594,2.833 2.229,2.833 false 3.01,1.958 3.01,1.396 3.01,1.396 2.719,1.396 false 0.323,0.938 0.323,0.583 0.323,0.583 0.802,0.583 false 2.271,0.781 2.49,0.969 0.219,0.188 10 false *1 0.375,2.021 0.583,2.198 0.208,0.177 10 false *2 0.896,0.51 1.115,0.677 0.219,0.167 10 false *3 2.01,2.771 2.208,2.938 0.198,0.167 10 false *2 2.521,1.333 2.708,1.51 0.188,0.177 10 false *3
*1 Front Disc Brake Pad
*2 No. 1 Anti-squeal Shim
*3 No. 2 Anti-squeal Shim


Install the No. 1 anti-squeal shims and No. 2 anti-squeal shims to the pads.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and directions as shown in the illustration.




Hide 04465 9.INSTALL FRONT DISC BRAKE PAD

a.
C323345C01
2.135,1.021 2.135,1.531 2.135,1.531 2.469,1.531 true 2.49,1.448 2.844,1.625 0.354,0.177 10 true SST
V113147

Expand


Using SST, push back the front disc brake piston.

NOTICE:

Do not forcibly install the piston into the disc brake cylinder assembly LH.


SST
09719-77020  


b.

Install the 2 front disc brake pads to the front disc brake cylinder mounting LH.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the front disc brake pads and front disc.



Hide 47750 10.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321869C01
1.333,2.333 0.885,2.125 0.885,2.125 0.646,2.125 false 1.979,2.573 1.76,2.75 1.76,2.75 1.625,2.75 false 0.427,2.042 0.604,2.229 0.177,0.188 10 false *a 1.448,2.667 1.604,2.865 0.156,0.198 10 false *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and install the disc brake cylinder assembly LH to the disc brake cylinder mounting LH with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


b.

Depress the brake pedal several times.


Hide 12.INSTALL FRONT WHEEL