Home › Brake › BRAKE (FRONT) › FRONT DISC BRAKE PAD(for 16 inch Front Disc Brake 2WD)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193995 FRONT DISC BRAKE PAD(for 16 inch Front Disc Brake 2WD) A

BRAKE (FRONT)  FRONT DISC BRAKE PAD(for 16 inch Front Disc Brake 2WD)  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



NOTICE:

After replacing the disc brake pads, the clearance between the disc brake pads and front discs becomes larger and the brake pedal feel becomes softer. Therefore, after replacing the disc brake pads, depress the brake pedal several times and check the clearance and brake pedal feel.


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 47750 3.REMOVE DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321904C01
1.979,2.135 2.104,2.01 2.104,2.01 2.26,2.01 true 1.333,2.125 0.958,2.406 0.958,2.406 0.74,2.406 true 0.542,2.323 0.74,2.521 0.198,0.198 10 false *a 2.271,1.927 2.469,2.094 0.198,0.167 10 true *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and remove the 2 bolts.


b.

Disconnect the disc brake cylinder assembly LH from the front disc brake cylinder mounting LH.


Hide 04465 4.REMOVE FRONT DISC BRAKE PAD

a.
C321897

Remove the 2 anti-squeal springs from the front disc brake pads.


b.

Remove the 2 front disc brake pads from the front disc brake cylinder mounting LH.


Hide 04945 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims from each pad.


Hide 6.REMOVE PAD WEAR INDICATOR PLATE

a.
C306284

Using a screwdriver, remove the pad wear indicator plates from the front disc brake pads as shown in the illustration.


Hide 7.INSTALL PAD WEAR INDICATOR PLATE

a.

Install the pad wear indicator plate to the inner lower side of the front disc brake pad.

NOTICE:

Install the pad wear indicator plate in the correct position and direction.



Hide 04945 8.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.

Install the 2 No. 1 anti-squeal shims to the front disc brake pads.

NOTICE:

When replacing a worn pad, the shims must be replaced together with the pads.



Hide 04465 9.INSTALL FRONT DISC BRAKE PAD

a.
C323345C01
2.135,1.021 2.135,1.531 2.135,1.531 2.469,1.531 true 2.49,1.448 2.844,1.625 0.354,0.177 10 true SST
V113147

Expand


Using SST, push back the front disc brake piston.

NOTICE:

Do not forcibly install the piston into the disc brake cylinder assembly LH.


SST
09719-77020  


b.

Install the 2 front disc brake pads to the front disc brake cylinder mounting LH.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the front disc brake pads and front disc.



c.
C321903

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




Hide 47750 10.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321896C01
1.948,2.063 2.031,1.885 2.031,1.885 2.146,1.885 true 1.333,2.208 0.948,2.438 0.948,2.438 0.74,2.438 true 0.51,2.354 0.729,2.521 0.219,0.167 10 false *a 2.188,1.802 2.375,1.969 0.188,0.167 10 true *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and install the disc brake cylinder assembly LH to the disc brake cylinder mounting LH with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the disc brake cylinder assembly LH while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




b.

Depress the brake pedal several times.


Hide 12.INSTALL FRONT WHEEL