Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0194112 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Proceed to
OK
NG



OK

2.INSPECT IG1 NO. 1 RELAY

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.INSPECT IG1 NO. 1 RELAY
a.

Remove the IG1 NO. 1 relay.


b.
A232574E02
3.198,1.523 3.303,1.667 0.105,0.143 10 3 2.815,1.606 3.17,1.606 false 3.198,1.049 3.303,1.192 0.105,0.143 10 5 2.815,1.132 3.17,1.132 false 1.926,0.319 2.031,0.462 0.105,0.143 10 1 2.325,0.702 2.04,0.403 false 3.198,0.319 3.303,0.462 0.105,0.143 10 2 2.921,0.714 3.176,0.403 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO. 1 RELAY)

NG

REPLACE IG1 NO. 1 RELAY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 NO. 1 RELAY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG1 NO. 1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-20 (IG1D) - IG1 NO. 1 relay terminal 1 Always Below 1 Ω
IG1 NO. 1 relay terminal 2 - Body ground Always Below 1 Ω
G69-20 (IG1D) or IG1 NO. 1 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT IG2 RELAY
a.

Remove the IG2 relay.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)

NG

REPLACE IG2 RELAY

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-20 (IG1D) - IG2 relay terminal 1 Always Below 1 Ω
IG2 relay terminal 2 - Body ground Always Below 1 Ω
G69-20 (IG1D) or IG2 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Install the IG1 NO. 1 relay.


c.

Install the IG2 relay.


d.

Measure the voltage while checking the Data List on the GTS.

C332681C01
1.854,0.479 2.313,0.74 0.458,0.26 1.563,2.406 1.771,2.406 1.771,2.406 1.958,1.635 true 0.219,0.115 0.531,0.313 0.313,0.198 10 false *a 1.958,0.531 2.417,0.729 0.458,0.198 10 false G69 1.229,2.333 1.844,2.531 0.615,0.198 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G69-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)