Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM33J0E _52 Drivetrain _038470 VF2CM TRANSFER / 4WD / AWD _0194120 TRANSFER ASSEMBLY G

VF2CM TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
C111637

Using a micrometer, measure the diameter of the transfer input shaft journal surface.

Minimum diameter:

47.59 mm (1.874 in.)


If the diameter is less than the minimum, replace the transfer input shaft.


b.
C111639

Using a dial indicator, measure the inside diameter of the transfer input shaft bushing.

Maximum inside diameter:

39.14 mm (1.540 in.)


If the inside diameter is more than the maximum, replace the transfer input shaft.


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C111642

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Standard clearance:

0.11 to 0.84 mm (0.00434 to 0.0330 in.)


Maximum clearance:

0.84 mm (0.0330 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


b.
C111643

Using a dial indicator, measure the radial clearance of the pinion gear.

Standard clearance:

0.009 to 0.038 mm (0.000355 to 0.00149 in.)


Maximum clearance:

0.038 mm (0.00149 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


Hide 36205 3.INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C111644

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


Maximum clearance:

0.25 mm (0.00984 in.)


If the thrust clearance is more than the maximum, replace the transfer drive sprocket sub-assembly.


b.
C111648

Using a dial indicator, measure the radial clearance between the drive sprocket and output shaft with the needle roller bearing installed.

Standard radial clearance:

0.010 to 0.055 mm (0.000394 to 0.00216 in.)


Maximum radial clearance:

0.055 mm (0.00216 in.)


If the radial clearance is more than the maximum, replace the transfer drive sprocket sub-assembly or needle roller bearing.


Hide 36231 4.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
G023146N03
0.521,0.792 0.677,0.99 0.156,0.198 10 false A 2.021,0.219 2.177,0.417 0.156,0.198 10 false B

Using a micrometer, measure the diameter of the rear transfer output shaft journal surface.

Minimum diameter:
Journal Diameter
A 27.98 mm (1.102 in.)
B 36.98 mm (1.456 in.)


If the diameter is less than the minimum, replace the rear transfer output shaft.


Hide 36236 5.INSPECT FRONT DRIVE CLUTCH SLEEVE AND NO. 1 TRANSFER GEAR SHIFT FORK CLEARANCE

a.
D030007

Using a feeler gauge, measure the clearance between the front drive clutch sleeve and No. 1 transfer gear shift fork.

Maximum clearance:

0.35 mm (0.0137 in.)


If the clearance is more than the maximum, replace the front drive clutch sleeve or No. 1 transfer gear shift fork.


Hide 36235 6.INSPECT TRANSFER HIGH AND LOW CLUTCH SLEEVE AND NO. 2 TRANSFER GEAR SHIFT FORK CLEARANCE

a.
D030008

Using a feeler gauge, measure the clearance between the transfer high and low clutch sleeve and No. 2 transfer gear shift fork.

Maximum clearance:

0.35 mm (0.0137 in.)


If the clearance is more than the maximum, replace the transfer high and low clutch sleeve or No. 2 transfer gear shift fork.


Hide 36410J 7.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY

a.

Inspect the transfer shift actuator assembly.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle.

If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay.

If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:
·

When inspecting the transfer shift actuator assembly, refer to the wiring diagram.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>SYSTEM DIAGRAM

·

When performing the operation described above, use the DEF relay.



i.

Check the 2WD to 4WD HIGH switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 2WD to 4WD HIGH position.

C325889C01
1.917,2.583 2.083,2.25 2.083,2.25 2.25,2.25 true 1.583,2.583 2,2 2,2 2.167,2 true 1.333,2.583 1.917,1.417 1.917,1.417 2.083,1.417 true 0.25,1.917 0.25,0.5 0.25,0.5 0.417,0.5 true 6.5,2.427 6.5,2.083 6.5,2.083 6.667,2.083 true 6.25,2.427 6.25,1.75 6.25,1.75 6.417,1.75 true 6,2.417 6,1.49 6,1.49 6.167,1.49 true 6.25,3 6.25,3.083 6.25,3.083 6.75,3.083 true 6.25,3.417 6.25,3.5 6.25,3.5 6.75,3.5 true 1,2.583 1,1 1,1 1.167,1 true 1.333,3 1.833,3.333 1.833,3.333 2,3.333 true 0.75,2.583 0.75,0.75 0.75,0.75 0.917,0.75 true 0.417,2.583 0.25,1.917 true 1,3 1.5,3.5 1.5,3.5 1.667,3.5 true 0.417,3 0.583,3.5 0.583,3.5 0.75,3.5 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.094,2.052 0.406,2.25 0.313,0.198 10 false *b 2.427,0.302 2.74,0.5 0.313,0.198 10 false *1 5.625,2.115 5.938,2.313 0.313,0.198 10 false *1 2.417,2.167 2.875,2.365 0.458,0.198 10 false TM2 2.292,1.917 2.75,2.115 0.458,0.198 10 false TM1 2.167,1.333 2.625,1.531 0.458,0.198 10 false TL1 0.542,0.417 1,0.615 0.458,0.198 10 false GND1 6.75,2 6.906,2.198 0.156,0.198 10 false 1 6.26,1.417 6.417,1.615 0.156,0.198 10 false 2 6.833,3.417 6.99,3.615 0.156,0.198 10 false 3 6.51,1.667 6.667,1.865 0.156,0.198 10 false 4 6.833,3 6.99,3.198 0.156,0.198 10 false 5 2.167,3.25 2.625,3.448 0.458,0.198 10 false L4 1.25,0.917 1.708,1.115 0.458,0.198 10 false TL2 1.042,0.667 1.5,0.865 0.458,0.198 10 false TL3 1.75,3.417 2.208,3.615 0.458,0.198 10 false GND 0.833,3.417 1.292,3.615 0.458,0.198 10 false B
*1 DEF Relay - -
*a 2WD to 4WD HIGH *b Component without harness connected
(Transfer Shift Actuator Assembly)


1.

After the 2WD to 4WD HIGH switch is complete, inspect the 4WD detection switch, L4 detection switch and limit switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (TL1) - 6 (GND1) After 2WD to 4WD HIGH switch is complete 10 kΩ or higher
4 (TL2) - 6 (GND1) After 2WD to 4WD HIGH switch is complete 10 kΩ or higher
5 (TL3) - 6 (GND1) After 2WD to 4WD HIGH switch is complete Below 1 Ω
9 (L4) - 6 (GND1) After 2WD to 4WD HIGH switch is complete 10 kΩ or higher
12 (B) - 10 (GND) After 2WD to 4WD HIGH switch is complete Below 1 Ω



If the result is not as specified, replace the transfer shift actuator assembly.


ii.

Check the 4WD HIGH to 4WD LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH to 4WD LOW position.

C325891C01
1.917,2.583 2.083,2.167 2.083,2.167 2.25,2.167 true 1.583,2.583 2,1.917 2,1.917 2.167,1.917 true 1.333,2.583 1.75,1.417 1.75,1.417 1.917,1.417 true 1,2.583 1,1.417 1,1.417 1.167,1.417 true 0.583,2.083 0.583,0.75 0.583,0.75 0.75,0.75 true 0.583,2.083 0.667,2.583 true 0.25,2.083 0.25,0.5 0.25,0.5 0.417,0.5 true 0.25,2.083 0.417,2.583 true 1.333,3 1.917,3.333 1.917,3.333 2.083,3.333 true 1,3 1.583,3.5 1.583,3.5 1.75,3.5 true 0.417,3 0.667,3.5 0.667,3.5 0.833,3.5 true 6.5,2.417 6.5,2.083 6.5,2.083 6.667,2.083 true 6.25,2.417 6.25,1.833 6.25,1.833 6.417,1.833 true 6,2.417 6,1.583 6,1.583 6.167,1.583 true 6.25,3 6.25,3.083 6.25,3.083 6.75,3.083 true 6.25,3.417 6.25,3.5 6.25,3.5 6.75,3.5 true 2.417,0.302 2.729,0.5 0.313,0.198 10 false *1 5.667,2.104 5.979,2.302 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.083,2.146 0.396,2.344 0.313,0.198 10 false *b 2.333,2.083 2.792,2.281 0.458,0.198 10 false TM2 2.25,1.833 2.708,2.031 0.458,0.198 10 false TM1 2,1.333 2.458,1.531 0.458,0.198 10 false TL1 1.25,1.333 1.708,1.531 0.458,0.198 10 false TL2 0.875,0.667 1.333,0.865 0.458,0.198 10 false TL3 0.5,0.417 0.958,0.615 0.458,0.198 10 false GND1 2.208,3.24 2.667,3.438 0.458,0.198 10 false L4 1.875,3.417 2.333,3.615 0.458,0.198 10 false GND 0.917,3.417 1.375,3.615 0.458,0.198 10 false B 6.75,2 7.063,2.198 0.313,0.198 10 false 1 6.521,1.75 6.833,1.948 0.313,0.198 10 false 4 6.271,1.5 6.583,1.698 0.313,0.198 10 false 2 6.844,2.969 7.156,3.167 0.313,0.198 10 false 5 6.844,3.417 7.156,3.615 0.313,0.198 10 false 3
*1 DEF Relay - -
*a 4WD HIGH to 4WD LOW *b Component without harness connected
(Transfer Shift Actuator Assembly)


1.

After the 4WD HIGH to 4WD LOW switch is complete, inspect the 4WD detection switch, L4 detection switch and limit switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (TL1) - 6 (GND1) After 4WD HIGH to 4WD LOW switch is complete 10 kΩ or higher
4 (TL2) - 6 (GND1) After 4WD HIGH to 4WD LOW switch is complete Below 1 Ω
5 (TL3) - 6 (GND1) After 4WD HIGH to 4WD LOW switch is complete 10 kΩ or higher
9 (L4) - 6 (GND1) After 4WD HIGH to 4WD LOW switch is complete Below 1 Ω
12 (B) - 10 (GND) After 4WD HIGH to 4WD LOW switch is complete Below 1 Ω



If the result is not as specified, replace the transfer shift actuator assembly.


iii.

Check the 4WD LOW to 4WD HIGH switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD LOW to 4WD HIGH position.

C325892C01
1.917,2.583 2.167,2.25 2.167,2.25 2.333,2.25 true 1.583,2.583 2,2 2,2 2.167,2 true 1.333,2.583 1.333,1.333 1.333,1.333 1.5,1.333 true 0.917,2.25 0.917,0.917 0.917,0.917 1.083,0.917 true 0.917,2.25 1,2.583 true 0.75,2.583 0.75,0.667 0.75,0.667 0.917,0.667 true 0.333,2.25 0.417,2.583 true 0.333,2.25 0.333,0.417 0.333,0.417 0.5,0.417 true 6.25,3 6.25,3.083 6.25,3.083 6.75,3.083 true 1,3 1.583,3.5 1.583,3.5 1.75,3.5 true 0.417,3 0.583,3.5 0.583,3.5 0.75,3.5 true 6.5,2.417 6.5,2.083 6.5,2.083 6.667,2.083 true 6.25,2.417 6.25,1.833 6.25,1.833 6.417,1.833 true 6,2.417 6,1.583 6,1.583 6.167,1.583 true 6.25,3.417 6.25,3.5 6.25,3.5 6.75,3.5 true 1.333,3 1.917,3.333 1.917,3.333 2.083,3.333 true 2.458,0.292 2.771,0.49 0.313,0.198 10 false *1 5.646,2.125 5.958,2.323 0.313,0.198 10 false *1 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.073,2.167 0.385,2.365 0.313,0.198 10 false *b 2.458,2.167 2.917,2.365 0.458,0.198 10 false TM2 2.25,1.917 2.708,2.115 0.458,0.198 10 false TM1 1.583,1.25 2.042,1.448 0.458,0.198 10 false TL1 1.167,0.833 1.625,1.031 0.458,0.198 10 false TL2 1.042,0.583 1.5,0.781 0.458,0.198 10 false TL3 0.583,0.333 1.042,0.531 0.458,0.198 10 false GND1 2.188,3.24 2.646,3.438 0.458,0.198 10 false L4 1.833,3.417 2.292,3.615 0.458,0.198 10 false GND 0.833,3.417 1.292,3.615 0.458,0.198 10 false B 6.75,2 7.063,2.198 0.313,0.198 10 false 1 6.5,1.75 6.813,1.948 0.313,0.198 10 false 4 6.25,1.5 6.563,1.698 0.313,0.198 10 false 2 6.844,3 7.156,3.198 0.313,0.198 10 false 5 6.844,3.417 7.156,3.615 0.313,0.198 10 false 3
*1 DEF Relay - -
*a 4WD LOW to 4WD HIGH *b Component without harness connected
(Transfer Shift Actuator Assembly)


1.

After the 4WD LOW to 4WD HIGH switch is complete, inspect the 4WD detection switch, L4 detection switch and limit switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (TL1) - 6 (GND1) After 4WD LOW to 4WD HIGH switch is complete 10 kΩ or higher
4 (TL2) - 6 (GND1) After 4WD LOW to 4WD HIGH switch is complete 10 kΩ or higher
5 (TL3) - 6 (GND1) After 4WD LOW to 4WD HIGH switch is complete Below 1 Ω
9 (L4) - 6 (GND1) After 4WD LOW to 4WD HIGH switch is complete 10 kΩ or higher
12 (B) - 10 (GND) After 4WD LOW to 4WD HIGH switch is complete Below 1 Ω



If the result is not as specified, replace the transfer shift actuator assembly.


iv.

Check the 4WD HIGH to 2WD switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the 4WD HIGH to 2WD position.

C325890C01
1.917,2.583 2.083,2.25 2.083,2.25 2.25,2.25 true 1.583,2.583 2,2 2,2 2.167,2 true 1.333,2.583 1.333,0.917 1.333,0.917 1.5,0.917 true 1,2.583 1,0.75 1,0.75 1.167,0.75 true 0.583,2.167 0.583,0.583 0.583,0.583 0.75,0.583 true 0.583,2.167 0.667,2.583 true 0.333,2.167 0.417,2.583 true 0.333,2.167 0.333,0.333 0.333,0.333 0.5,0.333 true 1,3 1.583,3.5 1.583,3.5 1.75,3.5 true 1.333,3 1.917,3.333 1.917,3.333 2.083,3.333 true 0.417,3 0.583,3.5 0.583,3.5 0.75,3.5 true 6.5,2.417 6.5,2.083 6.5,2.083 6.667,2.083 true 6.25,2.417 6.25,1.75 6.25,1.75 6.417,1.75 true 6,2.417 6,1.5 6,1.5 6.167,1.5 true 6.75,3.083 6.25,3.083 6.25,3.083 6.25,3 true 6.75,3.5 6.25,3.5 6.25,3.5 6.25,3.417 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 2.427,0.302 2.74,0.5 0.313,0.198 10 false *1 5.625,2.115 5.938,2.313 0.313,0.198 10 false *1 0.083,2.167 0.396,2.365 0.313,0.198 10 false *b 2.375,2.167 2.833,2.365 0.458,0.198 10 false TM2 2.25,1.917 2.708,2.115 0.458,0.198 10 false TM1 1.542,0.833 2,1.031 0.458,0.198 10 false TL1 1.25,0.667 1.708,0.865 0.458,0.198 10 false TL2 0.833,0.5 1.292,0.698 0.458,0.198 10 false TL3 0.625,0.25 1.219,0.448 0.594,0.198 10 false GND1 2.167,3.25 2.625,3.448 0.458,0.198 10 false L4 1.833,3.417 2.292,3.615 0.458,0.198 10 false GND 0.833,3.417 1.292,3.615 0.458,0.198 10 false B 6.75,2 7.063,2.198 0.313,0.198 10 false 1 6.521,1.667 6.833,1.865 0.313,0.198 10 false 4 6.271,1.417 6.583,1.615 0.313,0.198 10 false 2 6.844,3 7.156,3.198 0.313,0.198 10 false 5 6.833,3.417 7.146,3.615 0.313,0.198 10 false 3
*1 DEF Relay - -
*a 4WD HIGH to 2WD *b Component without harness connected
(Transfer Shift Actuator Assembly)


1.

After the 4WD HIGH to 2WD switch is complete, inspect the 4WD detection switch, L4 detection switch and limit switch.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (TL1) - 6 (GND1) After 4WD HIGH to 2WD switch is complete Below 1 Ω
4 (TL2) - 6 (GND1) After 4WD HIGH to 2WD switch is complete 10 kΩ or higher
5 (TL3) - 6 (GND1) After 4WD HIGH to 2WD switch is complete 10 kΩ or higher
9 (L4) - 6 (GND1) After 4WD HIGH to 2WD switch is complete 10 kΩ or higher
12 (B) - 10 (GND) After 4WD HIGH to 2WD switch is complete 10 kΩ or higher



If the result is not as specified, replace the transfer shift actuator assembly.