Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM33J0E _52 Drivetrain _038470 VF2CM TRANSFER / 4WD / AWD _0194120 TRANSFER ASSEMBLY A

VF2CM TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ACTUATOR BREATHER HOSE

a.
C325887

Disconnect the connection to the transfer shift actuator assembly, detach the 2 clamps, and then remove the actuator breather hose.


Hide 36102 2.REMOVE TRANSFER CASE COVER SUB-ASSEMBLY

a.
C325804

Remove the 4 bolts and transfer case cover sub-assembly.


b.
C325805

Remove the breather oil deflector.


Hide 33309B 3.REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front Side)

a.

Using a chisel and hammer, loosen the staked part of the transfer output shaft companion flange nut.

NOTICE:
·

Completely loosen the staked part of the lock nut when removing it.

·

Do not damage the threads of the driven sprocket.




b.
C325808C01
2.25,0.688 2.25,0.271 2.25,0.271 2.063,0.271 true 2.948,1.406 3.26,1.604 0.313,0.198 10 false *a 2.74,0.531 3.052,0.729 0.313,0.198 10 false *b 1.76,0.177 2.219,0.375 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST to hold the output shaft companion flange sub-assembly, remove the transfer output shaft companion flange nut.

SST
09330-00021  


c.
C325809C01
1.594,0.552 1.875,0.115 1.875,0.115 2.115,0.115 true 2.969,1.719 3.281,1.917 0.313,0.198 10 false *a 2.635,0.708 2.948,0.906 0.313,0.198 10 false *b 2.208,0.052 2.521,0.25 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the output shaft companion flange sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04031, 09957-04010, 09958-04011)

NOTICE:

Apply a lubricant to the threads and end of SST.



d.
C325810N01
0.792,1.583 0.375,1.073 0.375,1.073 0.823,1.26 true 0.073,1.01 0.531,1.208 0.458,0.198 10 false SST

Using SST and hammer, remove the transfer output shaft companion flange oil seal.

SST
09950-60010  (09951-00220, 09951-00290, 09952-06010)
09950-70010  (09951-07100)

NOTICE:

Be careful not to damage the transfer output shaft companion flange oil seal and output shaft companion flange sub-assembly contact surfaces.



Hide 33309C 5.REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear Side)

a.

Using a chisel and hammer, loosen the staked part of the transfer output shaft companion flange nut.

NOTICE:
·

Completely loosen the staked part of the transfer output shaft companion flange nut when removing it.

·

Do not damage the threads of the rear transfer output shaft.




b.
C325811C01
2.167,1.49 2.417,1.188 2.417,1.188 2.583,1.188 true 2.677,1.115 3.135,1.313 0.458,0.198 10 false SST 1.219,1.729 1.677,1.927 0.458,0.198 10 false *a 2.698,1.708 3.156,1.906 0.458,0.198 10 false *b
*a Turn
*b Hold


Using SST to hold the output shaft companion flange sub-assembly, remove the transfer output shaft companion flange nut and transfer output shaft O-ring.

SST
09330-00021  


c.
C325812C01
1.719,2 1.542,2 1.542,2 1.396,1.74 true 3,1.49 3.313,1.688 0.313,0.198 10 false *a 2.677,0.229 2.99,0.427 0.313,0.198 10 false *b 1.802,1.917 2.26,2.115 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the output shaft companion flange sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04031, 09957-04010, 09958-04011)

NOTICE:

Apply a lubricant to the threads and end of SST.



Hide 36115C 6.REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL

Hide 36115 7.REMOVE TRANSFER EXTENSION HOUSING

a.
C325813

Remove the 5 bolts and transfer extension housing.

HINT:

If necessary, tap the transfer extension housing with a plastic-faced hammer to remove it.



Hide 33309H 8.REMOVE TRANSFER OUTPUT SHAFT WASHER

a.
C325814C01
1.083,1.573 1.302,1.813 1.302,1.813 1.656,1.458 true 2.5,1.219 2.26,1.76 2.26,1.76 2.146,1.76 true 1.229,1.885 1.542,2.083 0.313,0.198 10 false *1 1.917,1.698 2.229,1.896 0.313,0.198 10 false *2
*1 Transfer Output Shaft Washer
*2 No. 2 Transfer Output Shaft Spacer


Remove the 2 transfer output shaft washers.


b.

Remove the No. 2 transfer output shaft spacer.


Hide 36114B 9.REMOVE NO. 1 TRANSFER CASE PLUG

a.
C325893C01
2.625,0.958 2.844,1.333 2.844,1.333 2.979,1.333 true 1.167,1.917 1.333,2.167 1.333,2.167 1.5,2.167 true 2.344,2.021 2.469,2.021 2.469,2.021 2.781,2.156 true 2.854,2.552 2.896,2.729 2.896,2.729 3.031,2.729 true 1.313,2.667 1.344,2.375 1.344,2.375 1.479,2.375 true 0.781,2.813 0.906,2.813 0.906,2.813 1.25,3.063 true 3.021,1.25 3.333,1.448 0.313,0.198 10 false *1 1.583,2.052 1.896,2.25 0.313,0.198 10 false *3 2.125,1.948 2.365,2.198 0.24,0.25 10 false *2 3.104,2.625 3.417,2.823 0.313,0.198 10 false *1 0.573,2.74 0.885,2.938 0.313,0.198 10 false *4 1.521,2.281 1.833,2.479 0.313,0.198 10 false *3
*1 No. 1 Transfer Case Plug (Filler Plug)
*2 No. 1 Transfer Case Gasket
*3 Transfer Drain Plug
*4 Transfer Drain Plug Gasket


Remove the No. 1 transfer case plug (filler plug) and No. 1 transfer case gasket.


b.

Remove the transfer drain plug and transfer drain plug gasket.


Hide 36112 10.REMOVE REAR TRANSFER CASE

a.
C325815C01
1.313,1.021 1.052,0.521 1.052,0.521 1.844,0.729 true 2.885,1.198 3.021,0.479 3.021,0.479 2.573,0.625 true 0.865,0.417 1.177,0.615 0.313,0.198 10 false *1 3.083,0.365 3.396,0.563 0.313,0.198 10 false *1
*1 Bracket


Remove the 12 bolts and 4 brackets.


b.

Remove the rear transfer case.

HINT:

If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



Hide 36104H 11.REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
C325828

Remove the 3 bolts and transfer oil separator sub-assembly.


b.

Remove the transfer case magnet.


Hide 36106 12.REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY

a.
C325829

Remove the 3 bolts and transfer oil pump body sub-assembly.


b.
C325831C01
2.219,1.01 2.5,0.667 2.5,0.667 2.667,0.667 true 2.75,0.563 3.063,0.76 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the transfer oil pump body O-ring.

NOTICE:

Be careful not to damage the transfer oil pump body sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
C325830

Remove the transfer oil pump gear.


Hide 36102G 13.REMOVE TRANSFER FRONT BEARING RETAINER SUB-ASSEMBLY

a.
C325806

Remove the 5 bolts and transfer front bearing retainer sub-assembly.

HINT:

If necessary, tap the transfer front bearing retainer sub-assembly with a plastic-faced hammer to remove it.



b.

for RC60F / RC61F:

Remove the O-ring.


Hide 36102L 14.REMOVE TRANSFER FRONT BEARING TYPE T OIL SEAL

a.
C325807C01
1.594,0.74 2.26,0.25 2.26,0.25 2.448,0.25 true 2.542,0.167 2.854,0.365 0.313,0.198 10 false *a
*a Protective Tape


for A750F, AC60F, R151F:

Using a screwdriver and hammer, remove the transfer front bearing type T oil seal.

NOTICE:

Be careful not to damage the transfer front bearing type T oil seal and transfer front bearing retainer sub-assembly contact surfaces.


HINT:

Tape the screwdriver tip before use.



b.

for RC60F / RC61F:

Using a screwdriver and hammer, remove the 2 transfer front bearing type T oil seals.

NOTICE:

Be careful not to damage the transfer front bearing type T oil seal and transfer front bearing retainer sub-assembly contact surfaces.


HINT:

Tape the screwdriver tip before use.



Hide 36270 15.REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C325832

Using a snap ring expander, remove the transfer low planetary gear bearing shaft snap ring.


b.
C325833

Remove the transfer low planetary gear assembly with the transfer input shaft.


Hide 36111C 16.REMOVE TRANSFER CASE PLUG

a.
C325834C01
1,1.667 1.167,2 1.167,2 1.333,2 true 1.167,0.75 1,0.75 1,0.75 0.75,1.417 true 0.833,0.5 0.667,0.5 0.667,0.5 0.417,1.167 true 1.448,1.906 1.76,2.104 0.313,0.198 10 false *1 1.25,0.667 1.563,0.865 0.313,0.198 10 false *2 0.906,0.427 1.219,0.625 0.313,0.198 10 false *3
*1 Transfer Case Plug
*2 Transfer Case Compression Spring
*3 Pin


Remove the transfer case plug, transfer case compression spring and pin.


Hide 36273 17.REMOVE TRANSFER LOW PLANETARY RING GEAR

a.
C325835C01
1.646,0.833 2.583,0.25 2.583,0.25 2.75,0.25 true 2.844,0.167 3.156,0.365 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the transfer low planetary ring gear hole snap ring.

NOTICE:

Be careful not to damage the front transfer case.


HINT:

Tape the screwdriver tip before use.



b.

Remove the transfer low planetary ring gear.


Hide 36284 18.REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE

a.
C325836C01
2.354,1.323 2.198,1.323 2.198,1.323 1.885,0.99 true 2.448,1.219 2.76,1.417 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the transfer low planetary gear shaft snap ring.

NOTICE:

Be careful not to damage the transfer low planetary gear assembly.


HINT:

Tape the screwdriver tip before use.



b.
C325837

Remove the transfer low planetary gear spline piece.


c.
C325838

Remove the transfer output shaft front needle roller bearing.


Hide 36211 19.REMOVE TRANSFER INPUT SHAFT

a.
C325839

Using a snap ring expander, remove the transfer input gear stopper shaft snap ring.


b.
C325840C01
2.875,0.219 2.958,0.219 2.958,0.219 2.958,0.469 true 2.594,0.979 2.708,0.979 2.708,0.979 3.031,1.146 true 2.458,1.583 2.708,1.583 true 2.688,0.156 3,0.354 0.313,0.198 10 false *1 2.396,0.906 2.708,1.104 0.313,0.198 10 false *2 2.26,1.5 2.573,1.698 0.313,0.198 10 false *3
*1 Transfer Input Gear Stopper
*2 Transfer Input Gear Stopper Ball
*3 Manual Transfer Planetary Carrier Washer


Remove the transfer input gear stopper and transfer input gear stopper ball.


c.

Remove the manual transfer planetary carrier washer.


d.
C325841C01
1.833,0.25 2,0.25 2,0.25 2,0.75 true 1.448,0.448 1.615,0.448 1.615,0.448 1.615,0.948 true 0.75,0.917 0.917,0.917 0.917,0.917 0.917,1.417 true 1.25,0.396 1.563,0.594 0.313,0.198 10 false *3 1.646,0.177 1.958,0.375 0.313,0.198 10 false *2 0.573,0.823 0.885,1.021 0.313,0.198 10 false *1
*1 Transfer Input Shaft
*2 Transfer Low Planetary Gear Bearing
*3 No. 1 Transfer Thrust Bearing Race


Remove the transfer input shaft, transfer low planetary gear bearing and No. 1 transfer thrust bearing race.


Hide 36216A 20.REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.
C325842

Remove the 2 No. 1 transfer input shaft seal rings.


Hide 36210A 21.REMOVE TRANSFER INPUT SHAFT BEARING

a.
C325843

Using a snap ring expander, remove the transfer input bearing shaft snap ring.


b.
C325844C01
0.531,1.063 1.531,1.479 true 1.188,0.781 0.51,1.052 0.51,1.052 1.188,1.677 true 3.021,0.583 3.333,0.781 0.313,0.198 10 false *a 0.396,1.719 0.708,1.917 0.313,0.198 10 false *b 0.146,0.969 0.615,1.25 0.469,0.281 10 false SST
*a Turn
*b Hold


Using SST, remove the transfer input shaft bearing.

SST
09555-55010  
09950-00030  
09950-60020  (09951-00630)

NOTICE:
·

Be careful not to damage the transfer low planetary gear assembly.

·

Apply a lubricant to the threads and end of SST.




Hide 36270A 22.REMOVE TRANSFER LOW PLANETARY GEAR BEARING

a.
C325845C01
2,1.438 2.458,1.656 2.458,1.656 2.073,1.656 true 2.469,1.156 2.781,1.354 0.313,0.198 10 false *a 1.24,0.344 1.552,0.542 0.313,0.198 10 false *b 2.521,1.573 2.833,1.771 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the transfer low planetary gear bearing.

SST
09527-10011  
09612-65014  (09612-01050, 09612-01060)

NOTICE:

Hook SST securely between the bearing and transfer low planetary gear.



Hide 36313F 23.REMOVE TRANSFER FRONT DRIVE SHIFT FORK SHAFT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



a.
C325816C01
0.656,0.375 0.792,0.375 false 0.594,0.708 0.729,0.708 false 0.594,1.052 0.729,1.052 false 0.823,0.302 1.135,0.5 0.313,0.198 10 false *1 0.781,0.615 1.094,0.813 0.313,0.198 10 false *2 0.781,0.969 1.094,1.167 0.313,0.198 10 false *3
*1 Shift Detent Ball Spring Plug
*2 Shift Detent Ball Compression Spring
*3 Shift Detent Ball


Using a 6 mm hexagon wrench, remove the 2 shift detent ball spring plugs.


b.

Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls.


c.
C325817

Using 2 screwdrivers and a hammer, remove the 2 transfer gear shift fork shaft snap rings.

HINT:

Use a piece of cloth to prevent the transfer gear shift fork shaft snap rings from flying off.



d.
C325818

Remove the bolt and transfer shift shaft stopper.


e.
C325819C01
0.615,1.813 0.823,1.813 0.823,1.813 1.448,1.188 true 0.917,0.417 1.083,0.417 1.083,0.417 1.083,1 true 2.24,1.198 2.615,1.719 2.615,1.719 2.76,1.719 true 0.688,0.333 1,0.531 0.313,0.198 10 false *1 0.427,1.74 0.74,1.938 0.313,0.198 10 false *3 2.875,1.646 3.188,1.844 0.313,0.198 10 false *2
*1 Transfer Front Drive Shift Fork Shaft
*2 No. 1 Transfer Gear Shift Fork
*3 No. 2 Transfer Gear Shift Fork


To remove the transfer front drive shift fork shaft, shift the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork to the positions shown in the illustration.


f.

Remove the transfer front drive shift fork shaft.


g.
C325820

Using a magnet hand, remove the 2 shift interlock pin or rollers.


Hide 36231 24.REMOVE REAR TRANSFER OUTPUT SHAFT, TRANSFER FRONT DRIVE CHAIN, TRANSFER DRIVEN SPROCKET

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



a.
C325821

Using 2 screwdrivers and a hammer, remove the transfer gear shift fork shaft snap ring.

HINT:
·

Use a piece of cloth to prevent the transfer gear shift fork shaft snap ring from flying off.

·

Remove only the transfer gear shift fork shaft snap ring on the front side of the transfer shift actuator shaft.




b.
C325822

Using a snap ring expander, remove the transfer output shaft shaft snap ring.


c.
C325823

Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the transfer output shaft rear, transfer driven sprocket and transfer front drive chain with the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork.


Hide 36410J 25.REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY

a.
C325824

Using 2 screwdrivers and a hammer, remove the transfer gear shift fork shaft snap ring.

HINT:

Use a piece of cloth to prevent the transfer gear shift fork shaft snap ring from flying off.



b.
C325825

Remove the 3 bolts and transfer shift actuator assembly.


Hide 36292A 26.REMOVE TRANSFER DRIVEN SPROCKET BEARING

a.
C325826N01
2.177,1.521 2.563,1.906 2.563,1.906 2.75,1.906 true 1.656,0.24 0.958,0.271 0.958,0.271 1.688,0.542 true 2.844,1.823 3.302,2.021 0.458,0.198 10 false SST 0.656,0.188 1.115,0.385 0.458,0.198 10 false SST

for Front Side:

Using SST and a press, remove the transfer driven sprocket bearing.

SST
09555-55010  
09950-60010  (09951-00210)
09950-70010  (09951-07100)

NOTICE:

Be careful not to drop or damage the driven sprocket.



b.
C325827N01
2.177,1.5 2.583,1.927 2.583,1.927 2.729,1.927 true 1.677,0.281 0.875,0.344 0.875,0.344 1.708,0.969 true 2.813,1.854 3.271,2.052 0.458,0.198 10 false SST 0.552,0.281 1.01,0.479 0.458,0.198 10 false SST

for Rear Side:

Using SST and a press, remove the transfer driven sprocket bearing.

SST
09555-55010  
09950-60010  (09951-00270)
09950-70010  (09951-07100)

NOTICE:

Be careful not to drop or damage the driven sprocket.



Hide 36237 27.REMOVE TRANSFER CLUTCH HUB

a.

Remove the transfer high and low clutch sleeve.


b.
C325847

Using a snap ring expander, remove the transfer clutch hub shaft snap ring.


c.
C325848N01
2.177,0.875 2.625,0.375 2.625,0.375 2.229,1.25 true 2.708,0.281 3.167,0.479 0.458,0.198 10 false SST

Using SST and a press, remove the transfer clutch hub.

SST
09527-10011  

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.



Hide 36205 28.REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

a.
C325849N01
2.104,0.927 2.531,0.229 2.531,0.229 2.698,0.229 true 2.771,0.146 3.229,0.344 0.458,0.198 10 false SST

Using SST and a press, remove the rear transfer output shaft radial ball bearing.

SST
09555-55010  

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.



b.
C325850C01
2.958,1.208 3.042,1.208 3.042,1.208 3.042,0.708 true 1.771,1.917 1.854,1.917 1.854,1.917 1.854,1.417 true 2.479,0.573 2.479,0.156 2.479,0.156 2.396,0.156 true 2.729,1.135 3.042,1.333 0.313,0.198 10 false *1 2.167,0.083 2.479,0.281 0.313,0.198 10 false *2 1.552,1.844 1.865,2.042 0.313,0.198 10 false *3
*1 No. 1 Transfer Output Shaft Spacer
*2 Needle Roller Bearing
*3 Transfer Drive Sprocket Sub-assembly


Remove the No. 1 transfer output shaft spacer.


c.

Remove the needle roller bearing.


d.

Remove the transfer drive sprocket sub-assembly.


Hide 36209 29.REMOVE TRANSFER SYNCHRONIZER RING SET (w/ A.D.D.)

a.
C325851

Remove the transfer synchronizer ring set.


Hide 36236 30.REMOVE FRONT DRIVE CLUTCH SLEEVE

a.
C325852C01
2.333,1.917 2.167,1.917 2.167,1.917 2,1.75 true 0.729,0.323 0.896,0.323 0.896,0.323 1.229,0.906 true 2.927,0.385 2.76,0.385 2.76,0.385 2.427,0.969 true 2.438,1.833 2.75,2.031 0.313,0.198 10 false *1 0.521,0.25 0.833,0.448 0.313,0.198 10 false *2 3,0.333 3.313,0.531 0.313,0.198 10 false *3
*1 Front Drive Clutch Sleeve
*2 Transfer Synchromesh Shifting Key Spring
*3 No. 1 Synchromesh Shifting Key


Remove the front drive clutch sleeve.

NOTICE:

w/ A.D.D.:

Be careful not to drop the 3 No. 1 synchromesh shifting keys.



b.

w/ A.D.D.:

Remove the 2 transfer synchromesh shifting key springs and 3 No. 1 synchromesh shifting keys.


Hide 36239 31.REMOVE TRANSFER DRIVE CLUTCH HUB

a.
C325853N01
0.958,1.135 0.438,0.771 0.438,0.771 1.292,1.906 true 0.115,0.688 0.573,0.885 0.458,0.198 10 false SST

Using SST and a press, remove the transfer drive clutch hub.

SST
09527-10011  

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.