After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "5" (S5 range) using the transmission control switch.
Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Tester Display |
|---|
| Sports Mode Selection SW |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Tester Display |
|---|
| Sports Shift Up SW |
| Sports Shift Down SW |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Disconnect the transmission control switch (transmission floor shift assembly) connector.
| *A | for LHD |
| *a | Component without harness connected
(Transmission Control Switch) |
for LHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SFTU) - 2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 3 (SFTU) - 2 (E) | Shift lever not held in "+" | 10 kΩ or higher |
| 1 (SFTD) - 2 (E) | Shift lever not held in "-" | 10 kΩ or higher |
| *A | for RHD |
| *a | Component without harness connected
(Transmission Control Switch) |
for RHD:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SFTU) - 2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 3 (SFTD) - 2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 1 (SFTU) - 2 (E) | Shift lever not held in "+" | 10 kΩ or higher |
| 3 (SFTD) - 2 (E) | Shift lever not held in "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transmission Control Switch (Transmission Floor Shift Assembly)) |
Disconnect the transmission control switch (transmission floor shift assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I1-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to TCM) |
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G90-22 (SFTU) - Body ground | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| G90-23 (SFTD) - Body ground | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| G90-22 (SFTU) - Body ground | Shift lever not held in "+" | 10 kΩ or higher |
| G90-23 (SFTD) - Body ground | Shift lever not held in "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Transmission Control Switch (Transmission Floor Shift Assembly)) |
Disconnect the transmission control switch (transmission floor shift assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in S, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transmission Control Switch (Transmission Floor Shift Assembly)) |
Disconnect the transmission control switch (transmission floor shift assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I1-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| I1-4 (IG) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I1 transmission control switch (transmission floor shift assembly) connector.
Disconnect the G90 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I1-5 (S) - G90-15 (S) | Always | Below 1 Ω |
| I1-5 (S) - Body ground | Always | 10 kΩ or higher |
| G90-15 (S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG