Home › Engine / Hybrid System › 1KD-FTV FUEL › FUEL SUPPLY PUMP
RM33J0E _51 Engine / Hybrid System _038430 1KD-FTV FUEL _0196041 FUEL SUPPLY PUMP A

1KD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel supply pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Fuel supply pump assembly Supply Pump Initialization Engine startability (Click here)
Timing belt Mode reset operation
·

Does not illuminate when replacement is necessary

·

Illuminates when replacement is not necessary


(Click here)

CAUTION:
·
A343702

Do not remove the radiator reservoir cap sub-assembly, vent plug, radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.


·
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 16400 3.REMOVE RADIATOR ASSEMBLY

Hide 11452 5.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23804C 6.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

a.
A347281

Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe sub-assembly from the common rail assembly and fuel supply pump assembly.


Hide 22100 7.REMOVE FUEL SUPPLY PUMP ASSEMBLY

NOTICE:
A347309

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.


a.
A231742C01
1.135,1.802 1.406,2.01 0.271,0.208 10 true *1 1.469,0.844 1.729,1.021 0.26,0.177 10 true *2
*1 Fuel Hose
*2 No. 1 Fuel Hose


Slide the 2 clamps and disconnect the fuel hose and No. 1 fuel hose from the fuel supply pump assembly.


b.
A231743

Disconnect the connector from the fuel temperature sensor.


c.

Disconnect the connector from the suction control valve.


d.
A070710

Remove the 4 bolts indicated by the arrows in the illustration.


e.

Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley from the injection gear.


f.
A301691N02
0.448,1.479 1.667,1.479 true 0.75,1.469 0.75,1.073 0.75,1.073 1.219,1.073 true 0.156,1.396 0.615,1.594 0.458,0.198 10 false SST

Remove the set nut and O-ring while holding the crankshaft pulley using SST.

SST
09213-58014  (91551-80840)
09330-00021  


g.
A257066

Loosen the 2 nuts.


h.
A070714N03
2.115,0.76 2.781,0.76 true 2.885,0.656 3.344,0.854 0.458,0.198 10 false SST

Using SST, disconnect the fuel supply pump assembly from the injection gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)

NOTICE:

Apply lubricant to the threads and tip of SST (center bolt) before using it.



i.

Remove the 2 nuts and fuel supply pump assembly from the timing gear case assembly.

NOTICE:
·

Do not hold or carry the fuel supply pump assembly by the pipe.

·

The fuel supply pump assembly must be kept horizontal.




j.

Remove the O-ring from the fuel supply pump assembly.