Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for Seat Cushion Bench Type)
RM33J0E _58 Vehicle Interior _038502 SEAT _0197342 REAR SEAT ASSEMBLY(for Seat Cushion Bench Type) A

SEAT  REAR SEAT ASSEMBLY(for Seat Cushion Bench Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 71485C 1.INSTALL REAR SEAT HINGE COVER RH

NOTICE:
·

Perform the following only when replacing the rear seat hinge cover RH.

·

Do not reuse the rear seat hinge cover RH after removing it.



a.
B402721C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to attach the guide.


b.

Push in installation direction (2) shown in the illustration to attach the claw to install a new rear seat hinge cover RH.


Hide 71486C 2.INSTALL REAR SEAT HINGE COVER LH

NOTICE:
·

Perform the following only when replacing the rear seat hinge cover LH.

·

Do not reuse the rear seat hinge cover LH after removing it.



HINT:

Use the same procedure described for the RH side.


Hide 78950 3.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

a.
B402714

Install the No. 1 fold seat stopper band assembly to the rear No. 2 seat lock assembly.


Hide 72630F 4.INSTALL REAR NO. 2 SEAT LOCK ASSEMBLY

a.
B409312

Install the rear No. 2 seat lock assembly together with the No. 1 fold seat stopper band assembly with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 71223 5.INSTALL REAR SEAT CUSHION SIDE BRACKET RH

a.
B409311

Install the rear seat cushion side bracket RH with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 71223 6.INSTALL REAR SEAT CUSHION SIDE BRACKET LH

HINT:

Use the same procedure described for the RH side.


Hide 79101 7.INSTALL NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY

a.
B409310

Install the No. 1 seat cushion frame sub-assembly together with the 2 rear seat cushion side brackets with the 2 bushes and 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 72995 8.INSTALL REAR SEAT CUSHION COVER RH

a.
B409309C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to attach the guide.


b.

Push in installation direction (2) shown in the illustration to attach the claw to install the rear seat cushion cover RH.


Hide 72998B 9.INSTALL REAR SEAT CUSHION COVER LH

HINT:

Use the same procedure described for the RH side.


Hide 10.INSTALL SEAT COVER WIRE

a.

Install the seat cover wire.

HINT:
·

Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

·

For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

·

Make sure to read the precautions before preparing the wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



B409307N01
2.365,1.313 2.417,1.042 true 4.76,1.313 4.813,1.042 true 4.094,1.135 4.365,0.823 true 3.177,1.125 2.823,0.833 true 5.198,0.854 5.688,0.813 true 5.208,0.417 5.698,0.375 true 1.5,0.885 1.99,0.844 true 1.5,0.448 1.99,0.406 true 3.885,0.448 4.375,0.406 true 2.813,0.417 3.292,0.479 true 4.667,0.625 4.844,0.219 true 2.25,0.635 2.469,0.208 true 2.302,1.323 2.458,1.521 0.156,0.198 10 true A 4.698,1.313 4.854,1.51 0.156,0.198 10 true A 5.781,0.729 5.938,0.927 0.156,0.198 10 true B 3.969,1.146 4.125,1.344 0.156,0.198 10 true B 3.25,1.125 3.406,1.323 0.156,0.198 10 true B 1.375,0.823 1.531,1.021 0.156,0.198 10 true B 2.51,0.031 2.667,0.229 0.156,0.198 10 true A 4.865,0.021 5.021,0.219 0.156,0.198 10 true A 5.75,0.292 5.906,0.49 0.156,0.198 10 true C 3.76,0.375 3.917,0.573 0.156,0.198 10 true C 3.344,0.406 3.5,0.604 0.156,0.198 10 true C 1.365,0.385 1.521,0.583 0.156,0.198 10 true C

Dimensions:
A 270 mm (10.63 in.)
B 180 mm (7.09 in.)
C 120 mm (4.72 in.)


HINT:
B376752

The dimensions shown in the illustration are the lengths.



Hide 79011A 11.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B409316N01
0.146,0.385 0.302,0.583 0.156,0.198 10 true A 0.406,0.49 0.563,0.688 0.156,0.198 10 true A 2.323,1.219 2.479,1.417 0.156,0.198 10 true B 2.573,1.313 2.729,1.51 0.156,0.198 10 true B 5.521,0.25 5.979,0.448 0.458,0.198 10 false B - B 3.792,0.26 4.25,0.458 0.458,0.198 10 false A - A



a.

Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad with 24 new hog rings in the order indicated in the illustration.

B409306C01
4.979,1.344 5.469,1.177 true 5.521,2.229 5.5,1.917 true 5.458,2.271 5.771,2.427 0.313,0.156 10 false *1 5.49,1.115 5.802,1.271 0.313,0.156 10 false *a 1.854,0.49 2.052,0.677 0.198,0.188 10 true (1) 1.865,0.719 2.063,0.906 0.198,0.188 10 true (2) 1.448,0.24 1.646,0.427 0.198,0.188 10 true (3) 1.125,0.229 1.323,0.417 0.198,0.188 10 true (4) 1.438,0.969 1.635,1.156 0.198,0.188 10 true (5) 1.094,0.969 1.292,1.156 0.198,0.188 10 true (6) 0.719,0.198 0.917,0.385 0.198,0.188 10 true (7) 0.719,0.375 0.917,0.563 0.198,0.188 10 true (8) 0.719,0.542 0.917,0.729 0.198,0.188 10 true (9) 0.667,0.729 0.927,0.917 0.26,0.188 10 true (10) 1.958,1.656 2.219,1.844 0.26,0.188 10 true (11) 1.958,1.844 2.219,2.031 0.26,0.188 10 true (12) 2.479,0.5 2.74,0.688 0.26,0.188 10 true (13) 2.479,0.698 2.74,0.885 0.26,0.188 10 true (14) 2.906,0.229 3.167,0.417 0.26,0.188 10 true (15) 3.219,0.229 3.479,0.417 0.26,0.188 10 true (16) 2.906,0.969 3.167,1.156 0.26,0.188 10 true (17) 3.24,0.979 3.5,1.167 0.26,0.188 10 true (18) 3.646,0.198 3.906,0.385 0.26,0.188 10 true (19) 3.656,0.365 3.917,0.552 0.26,0.188 10 true (20) 3.656,0.531 3.917,0.719 0.26,0.188 10 true (21) 3.656,0.708 3.917,0.896 0.26,0.188 10 true (22) 2.385,1.667 2.646,1.854 0.26,0.188 10 false (23) 2.385,1.833 2.646,2.021 0.26,0.188 10 false (24)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Be careful not to damage the No. 1 seat cushion cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 12.INSTALL REAR SEAT CUSHION COVER WITH PAD

a.
B409304C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly.


b.
B409302

Pass the No. 1 fold seat stopper band assembly through the hole of the No. 1 seat cushion cover sub-assembly.


c.
B409300

Close the 2 fasteners.


d.

Store the 2 fasteners.

B409298


e.
B409296

Attach the hook.


Hide 13.INSTALL SEAT COVER WIRE

a.

Install the seat cover wire.

HINT:
·

Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

·

For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

·

Make sure to read the precautions before preparing the wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



B409295N01
4.26,0.885 4.833,0.563 true 4.406,1.25 4.927,1.365 true 2.188,0.771 2.708,0.885 true 3.01,0.625 2.521,0.229 true 2.729,1.406 3.146,0.979 true 3.552,1.583 3.969,1.156 true 4.896,0.458 5.052,0.656 0.156,0.198 10 false A 2.365,0.083 2.521,0.281 0.156,0.198 10 false A 2.052,0.677 2.208,0.875 0.156,0.198 10 false B 4.969,1.302 5.125,1.5 0.156,0.198 10 false B 2.604,1.427 2.76,1.625 0.156,0.198 10 false B 3.438,1.552 3.594,1.75 0.156,0.198 10 false B

Dimensions:
A 270 mm (10.63 in.) B 300 mm (11.81 in.)


HINT:
B376752

The dimensions shown in the illustration are the lengths.



Hide 79013A 14.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B409315N01
0.323,0.354 0.479,0.552 0.156,0.198 10 true A 0.625,0.385 0.781,0.583 0.156,0.198 10 true A 2.344,0.698 2.5,0.896 0.156,0.198 10 true B 2.677,0.74 2.833,0.938 0.156,0.198 10 true B 3.323,0.26 4.094,0.458 0.771,0.198 10 false A - A 5,0.271 5.771,0.469 0.771,0.198 10 false B - B



a.

Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the No. 1 seatback pad with 12 new hog rings in the order indicated in the illustration.

B409294C01
4.938,0.656 5.427,0.583 true 5.5,1.458 5.438,1.25 true 5.438,1.51 5.75,1.667 0.313,0.156 10 false *1 5.479,0.49 5.792,0.646 0.313,0.156 10 false *a 1.354,0.313 1.542,0.51 0.188,0.198 10 true (1) 1.125,0.281 1.313,0.479 0.188,0.198 10 true (2) 2.385,0.531 2.573,0.729 0.188,0.198 10 true (3) 2.615,0.563 2.802,0.76 0.188,0.198 10 true (4) 1.594,0.75 1.781,0.948 0.188,0.198 10 true (5) 1.542,1.063 1.729,1.26 0.188,0.198 10 true (6) 2.01,0.896 2.198,1.094 0.188,0.198 10 true (7) 1.938,1.198 2.125,1.396 0.188,0.198 10 true (8) 0.74,0.635 0.927,0.833 0.188,0.198 10 true (9) 0.604,0.927 0.875,1.125 0.271,0.198 10 true (10) 2.875,0.99 3.146,1.188 0.271,0.198 10 true (11) 2.781,1.313 3.052,1.51 0.271,0.198 10 true (12)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Be careful not to damage the No. 1 seatback cover sub-assembly.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 15.INSTALL REAR SEATBACK COVER WITH PAD

a.
B409292C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to install the rear seatback cover with pad.


b.

Push in the rear end of the rear seatback cover with pad in installation direction (2) shown in the illustration.


c.

Attach the hooks in the order indicated in the illustration.

B409290N01
3.792,0.281 3.573,0.531 true 2.76,0.219 3.042,0.531 true 2.104,0.219 2.385,0.531 true 4.615,1.635 4.76,2.125 true 4.469,0.24 4.125,0.531 true 5.198,0.219 4.854,0.51 true 2.51,1.635 2.406,2.177 true 3.563,1.625 3.563,2.135 true 1.583,0.979 2.01,1.052 true 5.094,1.052 5.615,0.938 true 2.313,2.219 2.771,2.417 0.458,0.198 10 false (3) 3.823,0.094 4.281,0.292 0.458,0.198 10 false (1) 2.552,0.073 3.01,0.271 0.458,0.198 10 false (2) 4.5,0.094 4.958,0.292 0.458,0.198 10 false (2) 4.719,2.177 5.177,2.375 0.458,0.198 10 false (3) 3.479,2.177 3.938,2.375 0.458,0.198 10 false (4) 1.917,0.104 2.375,0.302 0.458,0.198 10 false (2) 1.365,0.896 1.823,1.094 0.458,0.198 10 false (5) 5.646,0.854 6.104,1.052 0.458,0.198 10 false (5) 5.208,0.083 5.667,0.281 0.458,0.198 10 false (2)


Hide 71931B 16.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.
B409289C01
0,0 0,0 false
V113147

Install in this Direction


w/o Center Headrest:

Attach the claw to install the 4 rear No. 1 seat headrest support assemblies.


b.
B410519C01
0,0 0,0 false
V113147

Install in this Direction


w/ Center Headrest:

Attach the claw to install the 6 rear No. 1 seat headrest support assemblies.


Hide 71960B 17.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Center Headrest)

a.

Install the rear seat center headrest assembly.


Hide 71940A 18.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the 2 rear seat headrest assemblies.


b.

Attach the No. 1 fold seat stopper band assembly to the stay of the rear seat headrest assembly and temporarily fix the rear seat cushion assembly in place.