The smart entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings.
The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
w/ Door Control Battery:
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
w/ Automatic Light Control System:
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Check that the wireless door lock functions operate normally.
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Disconnect the A38 wireless door lock buzzer connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 - G69-2 (BZR) | Always | Below 1 Ω |
| A38-2 - Body ground | Always | Below 1 Ω |
| A38-1 or G69-2 (BZR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the wireless door lock buzzer with a new or known good one.
for LHD:
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER(for LHD)>REMOVAL
for RHD:
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER(for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B