Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System)
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197661 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

E318144E04
5.604,0.75 6.063,0.948 0.458,0.198 10 false IND 5.448,1.667 5.906,1.865 0.458,0.198 10 false G16 5.469,1.823 6.875,2.188 1.406,0.365 10 false Transponder Key ECU Assembly 5.365,0.75 5.823,0.948 0.458,0.198 10 false 8 3.042,0.75 3.5,0.948 0.458,0.198 10 false LP 3.365,0.75 3.823,0.948 0.458,0.198 10 false 2 1.615,1.646 2.073,1.844 0.458,0.198 10 false H2 1.583,1.823 4.031,2.323 2.448,0.5 10 false Theft Warning Indicator Light Assembly (Security Indicator Light) 1.688,0.75 2.146,0.948 0.458,0.198 10 false E 1.469,0.75 1.927,0.948 0.458,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Theft warning indicator light assembly ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING INDICATOR LIGHT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING INDICATOR LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G16 transponder key ECU assembly connector.


b.

Disconnect the H2 theft warning indicator light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-2 (LP) - G16-8 (IND) Always Below 1 Ω
H2-6 (E) - Body ground Always Below 1 Ω
H2-2 (LP) - Body ground Always 10 kΩ or higher
G16-8 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the G16 transponder key ECU assembly connector.


b.
B405265C01
0.365,1.042 0.781,1.375 0.417,0.333 1.969,0.938 2.531,0.323 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 0.49,1.125 0.802,1.323 0.313,0.198 10 false H2 2.604,0.25 2.917,0.448 0.313,0.198 10 false LP
*a Front view of wire harness connector
(to Theft Warning Indicator Light Assembly)


Measure the voltage and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H2-2 (LP) - Body ground Ignition switch off Pulse generation
Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY