Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197662 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light does not illuminate. When the theft deterrent system is in the armed state, the body ECU blinks the security indicator light continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the body ECU illuminates the security indicator light.

WIRING DIAGRAM

E318151E03
5.615,0.75 6.073,0.948 0.458,0.198 10 false IND 5.323,0.75 5.781,0.948 0.458,0.198 10 false 17 5.698,1.813 7.021,2.063 1.323,0.25 10 false Body ECU 5.688,1.667 6.146,1.865 0.458,0.198 10 false G27 3.354,0.75 3.813,0.948 0.458,0.198 10 false 2 3.042,0.75 3.5,0.948 0.458,0.198 10 false LP 1.688,0.74 2.146,0.938 0.458,0.198 10 false E 1.448,0.75 1.906,0.948 0.458,0.198 10 false 6 1.656,1.656 2.115,1.854 0.458,0.198 10 false H2 1.646,1.823 4.063,2.333 2.417,0.51 10 false Theft Warning Indicator Light Assembly (Security Indicator Light) 6.365,0.427 6.823,0.625 0.458,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THEFT WARNING INDICATOR LIGHT ASSEMBLY - BODY ECU AND BODY GROUND)
a.

Disconnect the H2 theft warning indicator light assembly connector.


b.

Disconnect the G27 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-2 (LP) - G27-17 (IND) Always Below 1 Ω
H2-2 (LP) - Body ground Always 10 kΩ or higher
G27-17 (IND) - Body ground Always 10 kΩ or higher
H2-6 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY
a.

Remove the theft warning indicator light assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL


b.

Inspect the theft warning indicator light assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG