Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock) › 2015.06–2015.11
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0198001 DIFFERENTIAL SYSTEM(w/ Differential Lock) C

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  P17BB  Rear Differential Lock Position SW Stuck OFF  


DESCRIPTION

This DTC is output when an OFF malfunction of the rear differential lock position switch (No. 1 transfer indicator switch) is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17BB Rear Differential Lock Position SW Stuck OFF
·

Diagnosis Condition: With ignition switch turned to ON, rear differential is locked (differential lock coil operating)

·

Malfunction Status: With vehicle speed 5 km/h or higher, rear differential lock position switch (No. 1 transfer indicator switch) is stuck OFF

·

Malfunction Time: 3 seconds or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Rear differential lock position switch (No. 1 transfer indicator switch)



WIRING DIAGRAM

C325623E02
4.896,3.115 6.635,3.302 1.74,0.188 10 false 4 Wheel Drive Control ECU 4.917,2.917 5.375,3.115 0.458,0.198 10 false C39 5.281,2.344 5.74,2.542 0.458,0.198 10 false SLS 5.01,2.354 5.323,2.552 0.313,0.198 10 false 12 2.49,2.365 3.104,2.563 0.615,0.198 10 false RLY2 1.344,2.365 1.802,2.563 0.458,0.198 10 false GND 1.167,2.365 1.323,2.563 0.156,0.198 10 false 1 2.906,2.354 3.063,2.552 0.156,0.198 10 false 2 0.948,2.948 3.271,3.292 2.323,0.344 10 false Rear Differential Lock Position Switch (No. 1 Transfer Indicator Switch) 0.969,2.75 1.281,2.948 0.313,0.198 10 false F2 0.823,1.448 3.677,1.667 2.854,0.219 10 false Skid Control ECU (Brake Actuator Assembly) 3.302,0.635 3.615,0.833 0.313,0.198 10 false A3 3.635,0.635 3.948,0.833 0.313,0.198 10 false A4 3.354,0.427 3.51,0.625 0.156,0.198 10 false 9 3.625,0.417 3.938,0.615 0.313,0.198 10 false 11 3.344,0.854 3.656,1.052 0.313,0.198 10 false *1 3.635,0.865 3.948,1.063 0.313,0.198 10 false *2 3.677,3 4.5,3.198 0.823,0.198 10 false *1: w/o VSC 3.719,3.292 5.25,3.49 1.531,0.198 10 false *2: w/ VSC 6.094,1.427 6.406,1.625 0.313,0.198 10 false IG 2.885,0.51 3.198,0.688 0.313,0.177 10 false EXI3

CAUTION / NOTICE / HINT

HINT:

except Pre-Runner:

When the rear differential lock position switch (transfer indicator switch) is stuck OFF, if the transfer is set to H2, the vehicle is stopped and the ignition switch is turned from off to ON, the system returns to normal and this DTC is stored as a past DTC.

If the transfer is set to L4 again, the rear differential is locked and the vehicle is driven at 5 km/h or more, this DTC is output again.

for Pre-Runner:

When the rear differential lock position switch (transfer indicator switch) is stuck OFF, the vehicle is stopped and the ignition switch is turned from off to ON, the system returns to normal and this DTC is stored as a past DTC.

If the rear differential is locked and the vehicle is driven at 5 km/h or more, this DTC is output again.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - NO. 1 TRANSFER INDICATOR SWITCH)
a.

Disconnect the C39 4 wheel drive control ECU connector.


b.

Disconnect the F2 rear differential lock position switch (No. 1 transfer indicator switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-12 (SLS) - F2-2 (RLY2) Always Below 1 Ω
F2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.
C326785C02
1.521,0.74 1.938,0.979 0.417,0.24 1.948,2.042 2.406,2.75 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 1.646,0.771 1.958,0.969 0.313,0.198 10 false F2 2.406,2.792 2.792,2.99 0.385,0.198 10 false RLY2
*a Front view of wire harness connector
(to Rear Differential Lock Position Switch (No. 1 Transfer Indicator Switch))


Disconnect the F2 rear differential lock position switch (No. 1 transfer indicator switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F2-2 (RLY2) - Body ground Ignition switch ON 10 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 1 TRANSFER INDICATOR SWITCH

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU

3.CHECK NO. 1 TRANSFER INDICATOR SWITCH
a.

for Automatic Transmission:

Move the shift lever to N.

for Manual Transmission:

Move the shift lever to neutral.


b.

except Pre-Runner:

Switch the transfer position switch to L4.


c.

Lift up the vehicle until all four wheels are off the ground.


d.

Release the parking brake.


e.

Operate the differential lock switch to switch to locked.

HINT:

The rear differential lock indicator light continues to blink.



f.

Rotate one rear wheel in both directions and set the rear differential to the locked condition.

HINT:

When the rear differential is locked, rotating one rear wheel causes the other rear wheel to rotate in the same direction.



g.
C326637C02
1.667,0.604 2.052,0.865 0.385,0.26 1.74,1.531 1.104,2.5 true 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.74,0.646 2.198,0.844 0.458,0.198 10 false C39 0.948,2.542 1.406,2.74 0.458,0.198 10 false SLS
*a Component with harness connected
(4 Wheel Drive Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C39-12 (SLS) - Body ground Rear differential in locked condition Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG