1.INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH
Using SST and a press, press in the front differential side gear shaft bearing RH.
Using a snap ring expander, install the snap ring.
Install the snap ring securely.
41304F
2.INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
Install the differential side gear shaft sub-assembly RH to the front differential tube assembly.
Using a snap ring pliers, install a new snap ring.
Install the snap ring securely.
41304P
3.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH
41434
4.INSTALL DIFFERENTIAL CLUTCH HUB (w/ A.D.D.)
Install the differential clutch hub to the differential side gear shaft sub-assembly RH.
Using snap ring expander, install the side gear shaft hole snap ring.
Install the snap ring securely.
Make sure to install the differential clutch hub in the correct direction.
41331G
5.INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING
| *a | Front Differential Side Gear Needle Roller Bearing Depth |
Using SST and a press, press in 2 new front differential side gear needle roller bearings.
1.4 to 2.0 mm (0.0552 to 0.0787 in.)
6.ASSEMBLE DIFFERENTIAL CASE
Install 2 thrust washers to the 2 differential side gears.
Using the table below, select 2 differential side gear thrust washers which will ensure that the backlash is within the specifications.
| Thickness mm (in.) | Thickness mm (in.) |
|---|---|
| 1.48 to 1.52 (0.0583 to 0.0598) | 1.73 to 1.77 (0.0682 to 0.0696) |
| 1.53 to 1.57 (0.0603 to 0.0618) | 1.78 to 1.82 (0.0701 to 0.0716) |
| 1.58 to 1.62 (0.0622 to 0.0637) | 1.83 to 1.87 (0.0721 to 0.0736) |
| 1.63 to 1.67 (0.0642 to 0.0657) | 1.88 to 1.92 (0.0741 to 0.0755) |
| 1.68 to 1.72 (0.0662 to 0.0677) | - |
Install the 2 differential side gears, 2 differential pinion gears, 2 differential side gear thrust washers, 2 differential pinion gear thrust washers and differential pinion shaft to the differential case.
Align the holes of the differential case and differential pinion shaft.
Measure the side gear backlash.
Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.
0.15 mm (0.00590 in.) or less
If the backlash is not as specified, install 2 differential side gear thrust washers with different thicknesses.
Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the differential pinion shaft.
Stake the differential case.
7.INSTALL DIFFERENTIAL RING GEAR
Clean the contact surface of the differential case and differential ring gear.
Heat the differential ring gear in boiling water that is approximately 100°C (212°F).
Carefully remove the differential ring gear from the boiling water.
After the moisture on the differential ring gear has completely evaporated, quickly install the differential ring gear to the differential case.
| *a | Matchmark |
Align the matchmarks on the differential ring gear and differential case.
After the ring gear cools down, apply thread lock adhesive to the 10 set bolts and install them.
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
41311A
8.INSTALL FRONT DIFFERENTIAL CASE BEARING
Using SST and a press, press the 2 front differential case bearings (inner) onto the differential case.
41311A
9.INSTALL FRONT DIFFERENTIAL CASE BEARING
When replacing the 2 front differential case bearings, install the thinnest washer to each front differential case bearing. When reusing the front differential case bearings, install a new plate washer of the same thickness as the one that was removed to each front differential case bearing.
Using SST and a press, press in the front differential case bearing (outer) to the differential side bearing retainer.
Using SST and a press, press in the front differential case bearing (outer) to the differential carrier.
41211A
10.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING
| *1 | Front Drive Pinion Front Tapered Roller Bearing (Outer) |
| *a | Turn |
| *b | Hold |
Using SST, install the front drive pinion front tapered roller bearing (outer).
41211B
11.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using a brass bar and hammer, tap in a new front differential oil storage ring.
| *1 | Front Drive Pinion Rear Tapered Roller Bearing (Outer) |
| *a | Turn |
| *b | Hold |
Using SST, install the front drive pinion rear tapered roller bearing (outer).
41211A
12.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING
Install the drive pinion plate washer to the differential drive pinion.
First, install a drive pinion plate washer that has the same thickness as the removed drive pinion plate washer. After checking the tooth contact pattern, replace the drive pinion plate washer with one of a different thickness if necessary.
Using SST and a press, press the front drive pinion front tapered roller bearing (inner) onto the differential drive pinion.
13.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD
Install the differential drive pinion, front drive pinion rear tapered roller bearing (inner) and front differential drive pinion oil slinger.
Install the front differential drive pinion bearing spacer and front differential carrier oil seal after adjusting the gear contact pattern.
| *a | Turn |
| *b | Hold |
Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Adjust the differential drive pinion preload by tightening the front drive pinion companion flange nut.
| *a | Turn |
| *b | Hold |
Using SST to hold the front drive pinion companion flange sub-assembly with dust deflector in place, tighten the front drive pinion companion flange nut.
370 N*m (3773 kgf*cm, 273 ft.*lbf) or less
As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten it.
Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 0.98 to 1.92 N*m (10 to 19 kgf*cm, 9 to 16 in.*lbf) |
| Reused bearing | 0.97 to 1.81 N*m (10 to 18 kgf*cm, 9 to 16 in.*lbf) |
For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
Record the differential drive pinion preload for the total preload measurement.
14.INSTALL DIFFERENTIAL CASE ASSEMBLY
15.ADJUST DIFFERENTIAL RING GEAR BACKLASH
Install the side bearing retainer with the 10 bolts.
Using SST and a dial indicator, measure the ring gear backlash.
0.11 to 0.21 mm (0.00433 to 0.00826 in.)
If the backlash is not as specified, adjust it by either increasing or decreasing the number of washers on both sides equally.
There should be no clearance between the plate washer and case. Make sure that the ring gear has backlash.
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-50184 | 1.57 to 1.59 (0.0619 to 0.0625) | 90564-50194 | 1.87 to 1.89 (0.0737 to 0.0744) |
| 90564-50124 | 1.59 to 1.61 (0.0626 to 0.0633) | 90564-50134 | 1.89 to 1.91 (0.0744 to 0.0751) |
| 90564-50185 | 1.61 to 1.63 (0.0634 to 0.0641) | 90564-50195 | 1.91 to 1.93 (0.0752 to 0.0759) |
| 90564-50186 | 1.63 to 1.65 (0.0642 to 0.0649) | 90564-50196 | 1.93 to 1.95 (0.0760 to 0.0767) |
| 90564-50126 | 1.65 to 1.67 (0.0650 to 0.0657) | 90564-50136 | 1.95 to 1.97 (0.0768 to 0.0775) |
| 90564-50187 | 1.67 to 1.69 (0.0658 to 0.0665) | 90564-50197 | 1.97 to 1.99 (0.0776 to 0.0783) |
| 90564-50188 | 1.69 to 1.71 (0.0666 to 0.0673) | 90564-50198 | 1.99 to 2.01 (0.0784 to 0.0791) |
| 90564-50128 | 1.71 to 1.73 (0.0674 to 0.0681) | 90564-50138 | 2.01 to 2.03 (0.0792 to 0.0799) |
| 90564-50189 | 1.73 to 1.75 (0.0682 to 0.0688) | 90564-50199 | 2.03 to 2.05 (0.0800 to 0.0807) |
| 90564-50190 | 1.75 to 1.77 (0.0689 to 0.0696) | 90564-50200 | 2.05 to 2.07 (0.0808 to 0.0814) |
| 90564-50130 | 1.77 to 1.79 (0.0697 to 0.0704) | 90564-50140 | 2.07 to 2.09 (0.0815 to 0.0822) |
| 90564-50191 | 1.79 to 1.81 (0.0705 to 0.0712) | 90564-50201 | 2.09 to 2.11 (0.0823 to 0.0830) |
| 90564-50192 | 1.81 to 1.83 (0.0713 to 0.0720) | 90564-50202 | 2.11 to 2.13 (0.0831 to 0.0838) |
| 90564-50132 | 1.83 to 1.85 (0.0721 to 0.0728) | 90564-50142 | 2.13 to 2.15 (0.0839 to 0.0846) |
| 90564-50193 | 1.85 to 1.87 (0.0729 to 0.0736) | 90564-50203 | 2.15 to 2.17 (0.0847 to 0.0854) |
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-50204 | 1.57 to 1.59 (0.0619 to 0.0625) | 90564-50214 | 1.87 to 1.89 (0.0737 to 0.0744) |
| 90564-50154 | 1.59 to 1.61 (0.0626 to 0.0633) | 90564-50164 | 1.89 to 1.91 (0.0744 to 0.0751) |
| 90564-50205 | 1.61 to 1.63 (0.0634 to 0.0641) | 90564-50215 | 1.91 to 1.93 (0.0752 to 0.0759) |
| 90564-50206 | 1.63 to 1.65 (0.0642 to 0.0649) | 90564-50216 | 1.93 to 1.95 (0.0760 to 0.0767) |
| 90564-50156 | 1.65 to 1.67 (0.0650 to 0.0657) | 90564-50166 | 1.95 to 1.97 (0.0768 to 0.0775) |
| 90564-50207 | 1.67 to 1.69 (0.0658 to 0.0665) | 90564-50217 | 1.97 to 1.99 (0.0776 to 0.0783) |
| 90564-50208 | 1.69 to 1.71 (0.0666 to 0.0673) | 90564-50218 | 1.99 to 2.01 (0.0784 to 0.0791) |
| 90564-50158 | 1.71 to 1.73 (0.0674 to 0.0681) | 90564-50168 | 2.01 to 2.03 (0.0792 to 0.0799) |
| 90564-50209 | 1.73 to 1.75 (0.0682 to 0.0688) | 90564-50219 | 2.03 to 2.05 (0.0800 to 0.0807) |
| 90564-50210 | 1.75 to 1.77 (0.0689 to 0.0696) | 90564-50220 | 2.05 to 2.07 (0.0808 to 0.0814) |
| 90564-50160 | 1.77 to 1.79 (0.0697 to 0.0704) | 90564-50170 | 2.07 to 2.09 (0.0815 to 0.0822) |
| 90564-50211 | 1.79 to 1.81 (0.0705 to 0.0712) | 90564-50221 | 2.09 to 2.11 (0.0823 to 0.0830) |
| 90564-50212 | 1.81 to 1.83 (0.0713 to 0.0720) | 90564-50222 | 2.11 to 2.13 (0.0831 to 0.0838) |
| 90564-50162 | 1.83 to 1.85 (0.0721 to 0.0728) | 90564-50172 | 2.13 to 2.15 (0.0839 to 0.0846) |
| 90564-50213 | 1.85 to 1.87 (0.0729 to 0.0736) | 90564-50223 | 2.15 to 2.17 (0.0847 to 0.0854) |
16.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Item | Specified Condition |
|---|---|
| New bearing | 1.2 to 2.8 N*m (13 to 28 kgf*cm, 11 to 24 in.*lbf) |
| Reused bearing | 1.19 to 2.69 N*m (13 to 27 kgf*cm, 11 to 23 in.*lbf) |
Record the differential ring gear preload.
17.ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
Remove the differential case bearing retainer and differential case.
Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.
Install the differential case and differential case bearing retainer.
Hold the companion flange firmly in place and rotate the ring gear in both directions.
Remove the differential case bearing retainer and differential case.
Inspect the tooth contact pattern.
| *A | Drive Side | *B | Coast Side |
| *a | Proper Contact | *b | Toe Contact |
| *c | Face Contact | *d | Select an adjusting washer that will shift the drive pinion closer to the ring gear. |
| *e | Heel Contact | *f | Flank Contact |
| *g | Select an adjusting washer that will shift the drive pinion away from the ring gear. | *h | Heel Contact |
| *i | Flank Contact | *j | Toe Contact |
| *k | Face Contact | - | - |
| *1 | Drive Pinion Water |
If the teeth are not contacting properly, use the following chart to select a proper washer.
| Part No. | Thickness mm (in.) | Part No. | Thickness mm (in.) |
|---|---|---|---|
| 90564-35109 | 1.69 to 1.71 (0.0666 to 0.0673) | 90564-35120 | 2.02 to 2.04 (0.0796 to 0.0803) |
| 90564-35110 | 1.72 to 1.74 (0.0678 to 0.0685) | 90564-35121 | 2.05 to 2.07 (0.0807 to 0.0814) |
| 90564-35111 | 1.75 to 1.77 (0.0689 to 0.0696) | 90564-35123 | 2.08 to 2.10 (0.0819 to 0.0826) |
| 90564-35112 | 1.78 to 1.80 (0.0701 to 0.0708) | 90564-35124 | 2.11 to 2.13 (0.0831 to 0.0838) |
| 90564-35113 | 1.81 to 1.83 (0.0713 to 0.0720) | 90564-35125 | 2.14 to 2.16 (0.0843 to 0.0850) |
| 90564-35114 | 1.84 to 1.86 (0.0725 to 0.0732) | 90564-35126 | 2.17 to 2.19 (0.0855 to 0.0862) |
| 90564-35115 | 1.87 to 1.89 (0.0737 to 0.0744) | 90564-35127 | 2.20 to 2.22 (0.0867 to 0.0874) |
| 90564-35116 | 1.90 to 1.92 (0.0748 to 0.0755) | 90564-35128 | 2.23 to 2.25 (0.0878 to 0.0885) |
| 90564-35117 | 1.93 to 1.95 (0.0760 to 0.0767) | 90564-36129 | 2.26 to 2.28 (0.0890 to 0.0897) |
| 90564-35118 | 1.96 to 1.98 (0.0772 to 0.0779) | 90564-35130 | 2.29 to 2.31 (0.0902 to 0.0909) |
| 90564-35119 | 1.99 to 2.01 (0.0784 to 0.0791) | 90564-35131 | 2.32 to 2.34 (0.0914 to 0.0921) |
41204D
18.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT
41204D
19.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
41214C
20.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
41211B
21.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
22.REMOVE DIFFERENTIAL DRIVE PINION
41231F
23.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new front differential drive pinion bearing spacer to the differential drive pinion.
24.INSTALL DIFFERENTIAL DRIVE PINION
41211B
25.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Install the front drive pinion rear tapered roller bearing (inner) to the differential drive pinion.
41214C
26.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
27.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
41204D
28.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
29.INSTALL FRONT DIFFERENTIAL UNION
Install the front differential union to the differential side bearing retainer.
30.INSTALL DIFFERENTIAL SIDE BEARING RETAINER
Remove any old seal packing material from the differential side bearing retainer.
Do not drop oil on the contact surfaces of the differential carrier and differential side bearing retainer.
Clean residual seal packing material on the contact surface using gasoline or alcohol.
| *a | Seal Packing |
Apply seal packing to the differential side bearing retainer as shown in the illustration.
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
Install the differential side bearing retainer within 3 minutes after applying seal packing.
Install the differential side bearing retainer with the 10 bolts.
31.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Item | Specified Condition |
|---|---|
| New bearing | 1.3 to 2.9 N*m (14 to 29 kgf*cm, 12 to 25 in.*lbf) |
| Reused bearing | 1.29 to 2.79 N*m (14 to 28 kgf*cm, 12 to 24 in.*lbf) |
If necessary, disassemble and inspect the differential.
32.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH
Using SST and a dial indicator, measure the ring gear backlash.
0.11 to 0.21 mm (0.00433 to 0.00826 in.)
If the backlash is not within the specification, adjust the side bearing preload.
41204D
33.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
34.STAKE DRIVE PINION NUT
41304P
35.INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH
41183B
36.INSTALL FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR
Using a brass bar and hammer, tap in the front differential side bearing retainer deflector.
Make sure to install the front differential side bearing retainer deflector in the correct direction.
41306F
37.INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY (w/ A.D.D.)
Install a new side gear intermediate shaft hole snap ring to the differential side gear inter shaft sub-assembly.
Using a plastic-faced hammer, tap the differential side gear inter shaft sub-assembly into the differential case.
Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of axial play.
Check that the differential side gear inter shaft sub-assembly cannot be completely pulled out by hand.
41433
38.INSTALL DIFFERENTIAL CLUTCH SLEEVE (w/ A.D.D.)
Install the differential clutch sleeve.
41320
39.INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY
Remove any old seal packing material on the contact surfaces of the differential and clutch case.
Do not drop oil on the contact surfaces of the differential and clutch case.
Clean residual seal packing material on the contact surface using gasoline or alcohol.
| *a | Seal Packing |
Apply seal packing to the differential as shown in the illustration.
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
Install the differential tube within 3 minutes after applying seal packing.
Install the front differential tube to the differential.
w/ A.D.D.
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Using an E14 ''TORX'' socket wrench, install the 4 bolts.
w/o A.D.D.
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Using an E14 ''TORX'' socket wrench, install the 4 bolts.
41400B
40.INSTALL DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY (w/ A.D.D.)
| *a | Seal Packing |
Remove any seal packing material from the contact surface of the differential and clutch case. Also, do not drop oil on the contact surfaces.
Clean residual seal packing material from the contact surfaces using gasoline or alcohol.
Apply seal packing to the front differential tube as shown.
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
Install the actuator within 3 minutes after applying seal packing.
Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.
Install the differential motor actuator assembly to the front differential tube.
Install the 4 bolts.
89429
41.INSTALL OIL TEMPERATURE SENSOR
Install the oil temperature sensor to the front differential carrier assembly.