Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0199115 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 41110F 1.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

a.
C237477

Install the front No. 3 differential support to the front differential carrier assembly with the 2 bolts.

Torque:
107.9 N*m (1100 kgf*cm, 80 ft.*lbf)


b.

Support the front differential with a jack.


c.

Install the front differential carrier assembly.

C327404C01
0.323,0.063 0.635,0.26 0.313,0.198 10 false *a 0.354,2.073 0.667,2.271 0.313,0.198 10 false *b 4.333,0.083 4.646,0.281 0.313,0.198 10 false *a 4.333,1.958 4.646,2.156 0.313,0.198 10 false *b 4.271,4.135 4.583,4.333 0.313,0.198 10 false *a 4.26,6.031 4.573,6.229 0.313,0.198 10 false *b
*a Rear of Vehicle *b Side of Vehicle
V113147

Install in this Direction - -



d.
C323260

Install the differential mount nut.

Torque:
93.5 N*m (953 kgf*cm, 69 ft.*lbf)


e.
C323262C01
2.229,0.417 2.594,0.417 false 1.854,1.875 2.531,1.875 false 2.063,0.333 2.375,0.531 0.313,0.198 10 false *1 1.677,1.792 1.99,1.99 0.313,0.198 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper


Install the upper differential mount stopper and lower differential mount stopper to the front No. 2 differential support.


f.
C323258N01
0.49,1.208 0.646,1.406 0.156,0.198 10 true A 1.198,1.271 1.354,1.469 0.156,0.198 10 true A 2.958,1.406 3.115,1.604 0.156,0.198 10 true B

Install the front No. 2 mounting support with the 3 bolts and nut.

Torque:
Bolt A : 160 N*m (1632 kgf*cm, 118 ft.*lbf)
Bolt B : 105 N*m (1071 kgf*cm, 77 ft.*lbf)


g.
C323261C01
0.875,0.396 1.323,0.396 false 0.885,1.854 1.438,1.854 false 1.375,0.302 1.688,0.5 0.313,0.198 10 false *1 1.49,1.771 1.802,1.969 0.313,0.198 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper


Install the upper differential mount stopper and lower differential mount stopper to the front No. 1 differential support.


h.
C323259N01
2.552,0.052 2.698,0.24 0.146,0.188 10 true A 2.719,0.229 2.875,0.427 0.156,0.198 10 true A 3.052,0.208 3.208,0.406 0.156,0.198 10 true A 0.448,1.479 0.604,1.677 0.156,0.198 10 true B

Install the front No. 1 mounting support with the 4 bolts and nut.

Torque:
Bolt A : 186.2 N*m (1899 kgf*cm, 137 ft.*lbf)
Bolt B : 105 N*m (1071 kgf*cm, 77 ft.*lbf)


i.
C323256

Install the bracket with the bolt.

Torque:
18.55 N*m (189 kgf*cm, 14 ft.*lbf)


j.

w/ A.D.D.

i.

Connect the differential motor actuator connector.



k.
C323255

Install the bracket with the bolt.

Torque:
18.55 N*m (189 kgf*cm, 14 ft.*lbf)


l.

Connect the oil temperature sensor connector.


m.
C323254

Connect the hose to the front differential union.


n.
C323253

Install the differential breather tube bracket with the bolt.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


o.
C330144

w/ A.D.D.

i.

Connect the breather hose to the differential breather tube bracket.



p.

Lower the jack.


Hide 44200 2.INSTALL POWER STEERING LINK ASSEMBLY

a.

Remove the power steering link assembly with the 2 bolts, 2 washers and 2 nuts.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


Hide 45219 3.CONNECT STEERING SLIDING YOKE

Hide 31470 4.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

a.
C323257

Install the bracket with the bolt.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


b.

Install the clutch release cylinder with the 2 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 43420 5.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 6.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51442 9.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 10.INSTALL NO. 1 ENGINE UNDER COVER