Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER BLOCK
RM33J0E _51 Engine / Hybrid System _038447 2KD-FTV ENGINE MECHANICAL _0201076 CYLINDER BLOCK A

2KD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install the stud bolts to the cylinder block sub-assembly.

A303250C13
0.625,0.208 0.938,0.406 0.313,0.198 10 false *a 3.927,0.198 4.24,0.396 0.313,0.198 10 false *b 0.646,2.271 0.958,2.469 0.313,0.198 10 false *c 3.927,2.271 4.24,2.469 0.313,0.198 10 false *d 1.948,1.594 2.115,1.833 0.167,0.24 10 false A 4.458,0.188 4.646,0.396 0.188,0.208 10 false B 2.427,2.51 2.625,2.708 0.198,0.198 10 false C 5.458,2.375 5.677,2.573 0.219,0.198 10 false D 1.49,1.479 1.656,1.719 0.167,0.24 10 false A 0.969,1.615 1.135,1.854 0.167,0.24 10 false A 5.552,0.063 5.74,0.271 0.188,0.208 10 false B 2,3.042 2.198,3.24 0.198,0.198 10 false C 0.99,4.302 1.188,4.5 0.198,0.198 10 false C 5.656,2.375 5.875,2.573 0.219,0.198 10 false D 1.375,6.948 1.573,7.146 0.198,0.198 10 false A 5.229,6.938 5.427,7.135 0.198,0.198 10 false B 1.344,7.094 1.698,7.292 0.354,0.198 10 false M6 5.188,7.094 5.531,7.302 0.344,0.208 10 false M6 2.635,0.75 2.823,0.958 0.188,0.208 10 false B 1.208,4.813 1.479,5 0.271,0.188 10 false *e 5.24,8.458 5.438,8.656 0.198,0.198 10 false D 5.188,8.615 5.531,8.823 0.344,0.208 10 false M6 1.385,8.458 1.583,8.656 0.198,0.198 10 false C 1.344,8.615 1.688,8.823 0.344,0.208 10 false M6 1.219,6.729 1.49,6.917 0.271,0.188 10 false *e 2.438,5.813 2.708,6 0.271,0.188 10 false *f 4.813,5.958 5.083,6.146 0.271,0.188 10 false *g 4.833,6.688 5.104,6.875 0.271,0.188 10 false *g 4.844,7.698 5.115,7.885 0.271,0.188 10 false *e 4.865,8.208 5.135,8.396 0.271,0.188 10 false *e 6.063,6.385 6.333,6.573 0.271,0.188 10 false *h 1.229,7.635 1.5,7.823 0.271,0.188 10 false *i 1.25,8.156 1.521,8.344 0.271,0.188 10 false *i 2.406,7.979 2.677,8.167 0.271,0.188 10 false *j 6.073,7.969 6.344,8.156 0.271,0.188 10 false *k
*a Front Side *b Left Side
*c Oil Pan Side *d Right Side
*e 9 mm (0.354 in.) *f 69 mm (2.72 in.)
*g 9.5 mm (0.374 in.) *h 29 mm (1.14 in.)
*i 12 mm (0.472 in.) *j 26 mm (1.02 in.)
*k 23 mm (0.906 in.) - -



Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A060268

Align the pin of the No. 1 oil nozzle sub-assembly with the pin hole of the cylinder block sub-assembly.


b.

Install the 4 No. 1 oil nozzle sub-assemblies with the 4 check valves.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A060203

Using a small screwdriver, install a new snap ring on one side of the piston pin hole.


b.

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.


d.
A253396C08
1,1.063 1.167,1.302 1.167,1.302 1.167,1.333 false 0.885,2.365 0.344,2.365 true 1.083,1.344 1.26,1.51 0.177,0.167 10 false *1 0.135,2.271 0.313,2.438 0.177,0.167 10 false *2
*a Front Mark (Arrow)
*b Front Mark (Protrusion)


Align the front marks of the piston and connecting rod, connect the connecting rod to the piston, and then push in the piston pin with your thumb.


e.

Check the fit between the piston and piston pin. Try to move the piston back and forth on the piston pin.


f.
A149754

Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.


Hide 13011 4.INSTALL PISTON RING SET

a.
A226794C06
1.688,0.146 1.688,0.469 false 1.594,1.917 1.76,2.073 0.167,0.156 10 false *b 1.594,0.49 1.76,0.646 0.167,0.156 10 false *a
*a Coil Joint
*b Oil Ring End Gap


Install the coil and oil ring by hand.

HINT:

Make sure the end gap of the oil ring and the coil joint are on opposite sides.



b.
A226155C02
0.698,0.698 0.375,0.302 0.375,0.302 0.292,0.302 false 0.698,1.396 0.375,1.052 0.375,1.052 0.292,1.052 false 0.063,0.219 0.26,0.385 0.198,0.167 10 false *1 0.073,0.979 0.271,1.146 0.198,0.167 10 false *2
*1 No. 1 Piston Ring
*2 No. 2 Piston Ring


Using a piston ring expander, install the No. 1 piston ring and No. 2 piston ring with the code marks facing upward.

Code Mark:
Item Specified Condition
No. 1 Piston Ring NP
No. 2 Piston Ring N2



c.
A256571C05
1.219,1.208 0.833,0.833 0.833,0.833 0.667,0.833 true 0.823,0.385 1.083,0.573 0.26,0.188 10 false *1 2.469,0.417 2.75,0.604 0.281,0.188 10 false *2 2.427,1.656 2.792,1.948 0.365,0.292 10 false *4 0.823,1.583 1.167,1.792 0.344,0.208 10 false *3 0.469,0.75 0.75,1.01 0.281,0.26 10 false *a
*1 No. 1 Piston Ring
*2 Oil Ring
*3 Coil
*4 No. 2 Piston Ring
*a Front Mark (Arrow)


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



Hide 11711 5.INSTALL CRANKSHAFT BEARING

A060228

HINT:

Upper crankshaft bearings have an oil groove and oil hole. Lower crankshaft bearings do not.


a.

Align the crankshaft bearing claw with the claw groove of the cylinder block sub-assembly and push in the 5 upper crankshaft bearings.


b.
A060190

Align the crankshaft bearing claw with the claw groove of the crankshaft bearing cap and push in the 5 lower crankshaft bearings.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Place the crankshaft on the cylinder block sub-assembly.


b.
A060188

Push the crankshaft in one direction and install one crankshaft thrust washer to the No. 5 journal position with the oil groove facing outward.


c.

Push the crankshaft in the opposite direction and install the other crankshaft thrust washer to the No. 5 journal position with the oil groove facing outward.


d.
A060189

Install the 2 crankshaft thrust washers to the No. 5 bearing cap with the grooves facing outward.


e.
A060226

Install the 5 crankshaft bearing caps to their proper locations.


f.
A060270N05
0.813,0.427 0.958,0.625 0.146,0.198 10 false 4 3.135,1.135 3.281,1.333 0.146,0.198 10 true 8 1.875,0.021 2.021,0.219 0.146,0.198 10 false 6 2.073,1.583 2.219,1.781 0.146,0.198 10 true 2 1.406,0.177 1.552,0.375 0.146,0.198 10 true 1 1.49,1.823 1.635,2.021 0.146,0.198 10 true 5 0.875,1.979 1.021,2.177 0.146,0.198 10 true 9 3.01,0.063 3.156,0.26 0.146,0.198 10 true 7 2.615,1.333 2.76,1.531 0.146,0.198 10 true 3 0.125,0.667 0.375,0.865 0.25,0.198 10 false 10

Install the crankshaft bearing cap set bolts.

HINT:
·

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.

·

If a crankshaft bearing cap set bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the bolt heads of the crankshaft bearing cap set bolts.


ii.

Install and uniformly tighten the 10 crankshaft bearing cap set bolts of the crankshaft bearing caps in several passes in the sequence shown in the illustration.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

If any one of the crankshaft bearing cap set bolts does not meet the torque specification, replace the crankshaft bearing cap set bolt.


iii.
A303251C04
0.844,0.917 0.844,0.802 0.844,0.802 0.646,0.344 true 0.125,0.208 0.354,0.438 0.229,0.229 10 false 90° 1.198,0.167 1.427,0.396 0.229,0.229 10 false 90° 0.354,0.615 0.583,0.844 0.229,0.229 10 false *a 0.75,0.948 0.979,1.177 0.229,0.229 10 false *b
*a Front
*b Paint Mark


Mark the front of each crankshaft bearing cap bolt with paint.


iv.

Tighten the crankshaft bearing cap set bolts by 90° in the numerical order shown in the previous illustration.


v.

Check that the painted marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

Hide 13041 8.INSTALL CONNECTING ROD BEARING

a.

Align the connecting rod bearing claw with the groove of the connecting rod or connecting rod cap.


b.

Install the connecting rod bearings to the connecting rod and connecting rod cap.


Hide 9.INSTALL PISTON AND CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons and the surfaces of the connecting rod bearings.


b.

Check the positions of the piston ring ends.


c.
A256738C06
0.313,0.74 0.5,0.927 0.188,0.188 10 false *a
*a Front Mark (Arrow)


Using a piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.


d.

Place the connecting rod cap on the connecting rod.

i.
A303252C05
0.583,0.708 0.406,1.333 0.406,1.333 0.469,0.698 true 0.292,1.354 0.604,1.552 0.313,0.198 10 false *a
*a Matchmark


Match each numbered connecting rod cap with the correct connecting rod.


ii.
A060237

Align the pins of the connecting rod cap with the pin holes of the connecting rod and install the connecting rod cap.


iii.
A060238C06
1.396,0.844 0.667,1.292 0.667,1.292 0.667,1.396 true 0.563,1.417 0.75,1.583 0.188,0.167 10 false *a
*a Front Mark (Protrusion)
V100135

Front


Check that the front mark of the connecting rod cap is facing forward.



e.

Install the connecting rod bolts.

HINT:
·

The connecting rod bolts are tightened in 2 progressive steps.

·

If any connecting rod bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


ii.

Install and alternately tighten the connecting rod bolts of the connecting rod cap in several passes.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:

If any one of the connecting rod bolts does not meet the torque specification, replace the connecting rod bolt.



iii.
A060197C06
0.5,0.365 0.625,0.99 0.625,0.99 0.625,1.052 true 0.406,0.01 0.74,0.198 0.333,0.188 10 false 90° 0.969,0.146 1.302,0.333 0.333,0.188 10 false 90° 0.198,0.594 0.375,0.792 0.177,0.198 10 false *a 0.531,1.063 0.719,1.208 0.188,0.146 10 false *b
*a Front
*b Paint Mark


Mark the front of each connecting rod bolt with paint.


iv.

Tighten the connecting rod bolts by 90° as shown in the illustration.


v.

Check that the painted marks are now at a 90° angle to the front.



f.

Check that the crankshaft turns smoothly.


Hide 10.INSPECT CONNECTING ROD THRUST CLEARANCE

Hide 11448 11.INSTALL CYLINDER BLOCK OIL ORIFICE