Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMT Made)
RM33J0E _52 Drivetrain _038471 DRIVE SHAFT / PROPELLER SHAFT _0201199 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  REMOVAL  


PROCEDURE

Hide 51569 1.REMOVE PROPELLER SHAFT GUARD

a.

for 2WD and Pre-Runner:

i.
C317873

for Transmission side:

Remove the 2 bolts and propeller shaft guard.


ii.
C317875

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



b.

for 4WD:

i.
C317869

for Transfer side:

Remove the 2 bolts and propeller shaft guard.


ii.
C317870

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



Hide 37100 2.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD and Pre-Runner)

a.
C317876C01
1.729,1.542 2.427,1.854 2.427,1.854 1.708,1.396 true 2.469,1.781 2.844,2.01 0.375,0.229 10 true *a
*a Matchmark


for R151:

Place matchmarks on the propeller shaft flange and differential flange.


b.
C317880C01
1.656,4.021 2.531,4.177 2.531,4.177 1.667,3.938 true 1.75,1.479 2.438,1.906 2.438,1.906 1.75,1.594 true 2.583,4.104 2.896,4.302 0.313,0.198 10 true *a 2.521,1.844 2.833,2.042 0.313,0.198 10 true *a
*a Matchmark


for RC60, RC61:

Place matchmarks on the propeller shaft flange, differential torsional damper and differential flange.


c.

for Differential Type BD20:

Remove the 4 nuts, 4 bolts and 4 washers and disconnect the propeller shaft.


d.

for Differential Type BD22:

Remove the 4 nuts and 4 washers and disconnect the propeller shaft.


e.
C317877

Remove the 2 set bolts of the center support bearing from the frame crossmember.


f.

Pull out the propeller shaft with center bearing assembly.

NOTICE:

When pulling out the propeller shaft, make sure that transmission fluid does not leak from the extension housing.


HINT:

Transmission fluid may leak from the extension housing there fore, use a container to catch the fluid.



g.
C317881

for RC60, RC61:

Remove the differential torsional damper.


Hide 37100 3.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

a.
C317863C01
1.615,1.469 2.146,1.979 2.146,1.979 1.646,1.365 true 2.208,1.906 2.521,2.104 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and transfer flange.


b.

Remove the 4 nuts and 4 washers and disconnect the propeller shaft.


c.
C317864C01
1.573,1.469 2.188,1.854 2.188,1.854 1.573,1.385 true 2.281,1.792 2.594,1.99 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and differential flange.


d.

Remove the 4 nuts and 4 washers.


e.
C317877

Remove the 2 set bolts of the center No. 1 support bearing assembly from the frame crossmember.


f.

Remove the propeller shaft with center bearing assembly.