33428
1.INSPECT COUNTERSHAFT 5TH GEAR
Using a cylinder gauge, measure the inside diameter of the countershaft 5th gear.
38.015 to 38.040 mm (1.4967 to 1.4976 in.)
38.040 mm (1.4976 in.)
If the inside diameter is more than the maximum, replace the countershaft 5th gear.
2.INSPECT COUNTERSHAFT 5TH GEAR THRUST CLEARANCE
Using a feeler gauge, measure the thrust clearance.
0.10 to 0.35 mm (0.00394 to 0.0137 in.)
If the clearance is not as specified, replace the countershaft 5th gear.
3.INSPECT COUNTERSHAFT 5TH GEAR RADIAL CLEARANCE
Using a dial indicator, measure the radial clearance.
0.015 to 0.068 mm (0.000591 to 0.00267 in.)
If the clearance is not as specified, replace the counter 5th gear bearing.
33368
4.INSPECT NO. 2 SYNCHRONIZER RING
Apply gear oil to the cone of the input shaft, and check that it does not turn in either direction while pushing the No. 2 synchronizer ring.
If it can turn, replace the No. 2 synchronizer ring.
Push the No. 2 synchronizer ring against the cone of the input shaft. Measure the clearance between the No. 2 synchronizer ring and input shaft.
0.7 to 1.7 mm (0.0276 to 0.0669 in.)
If the clearance is not as specified, replace the No. 2 synchronizer ring.
33384A
5.INSPECT NO. 3 SYNCHRONIZER RING
Apply gear oil to the cone part of the No. 5 gear spline piece, and check that it does not turn in either direction while pushing the No. 3 synchronizer ring against the No. 5 gear spline piece.
If it can turn, replace the No. 3 synchronizer ring.
Push the No. 3 synchronizer ring against the cone part of the No. 5 gear spline piece. Measure the clearance between the No. 3 synchronizer ring and No. 5 gear spline piece.
0.68 to 1.32 mm (0.0268 to 0.0519 in.)
If the clearance is not as specified, replace the No. 3 synchronizer ring.
33212A
6.INSPECT NO. 1 GEAR SHIFT FORK
Using a vernier caliper, measure the No. 1 gear shift fork groove A and the thickness B.
5.20 to 5.36 mm (0.205 to 0.211 in.)
5.36 mm (0.211 in.)
4.35 to 4.65 mm (0.172 to 0.183 in.)
4.35 mm (0.172 in.)
If the width is not as specified, replace the No. 1 gear shift fork.
33213G
7.INSPECT NO. 2 GEAR SHIFT FORK
Using a vernier caliper, measure the thickness of the claw part of the No. 2 gear shift fork.
9.9 to 10.0 mm (0.390 to 0.393 in.)
9.9 mm (0.390 in.)
If the width is not as specified, replace the No. 2 gear shift fork.
33214G
8.INSPECT NO. 3 GEAR SHIFT FORK
| *a | Pad |
Using a vernier caliper, measure the thickness of the claw part of the No. 3 gear shift fork.
9.76 to 10.24 mm (0.385 to 0.403 in.)
9.76 mm (0.385 in.)
Check the thickness including the pad.
If the measurement result is less than the minimum or the pad is damaged, replace the No. 3 gear shift fork.
33395
9.INSPECT NO. 3 TRANSMISSION HUB SLEEVE
Check the sliding condition between the countershaft 5th gear and No. 3 transmission hub sleeve.
Check the spline gear of the No. 3 transmission hub sleeve for wear.
If there are any defects, replace the No. 3 transmission hub sleeve.
Using a vernier caliper, measure the No. 3 transmission hub sleeve groove.
10.5 to 10.6 mm (0.414 to 0.417 in.)
10.6 mm (0.417 in.)
If the width is not as specified, replace the No. 3 transmission hub sleeve.
33402
10.INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY
Using a caliper gauge, measure the inside diameter of the reverse idler gear sub-assembly.
24.040 to 24.061 mm (0.9465 to 0.9472 in.)
24.061 mm (0.9472 in.)
If the inside diameter is more than the maximum, replace the reverse idler gear sub-assembly.
Using a micrometer, measure the diameter of the sliding part of the reverse idler gear sub-assembly on the reverse idler gear shaft.
23.979 to 24.000 mm (0.9441 to 0.9448 in.)
23.979 mm (0.9441 in.)
If the diameter is less than the minimum, replace the reverse idler gear shaft.
Using a feeler gauge, measure the thrust clearance of the shoe part between the reverse idler gear sub-assembly and reverse shift arm.
0.05 to 0.35 mm (0.00197 to 0.0137 in.)
If the clearance is not as specified, replace the reverse idler gear sub-assembly and reverse shift arm.