Home › Engine / Hybrid System › 2GD-FTV FUEL › FUEL FILTER
RM33J0E _51 Engine / Hybrid System _038439 2GD-FTV FUEL _0199082 FUEL FILTER A

2GD-FTV FUEL  FUEL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

When replacing the fuel filter element assembly, use TOYOTA genuine parts.

·

When replacing the fuel filter element assembly, clean the fuel filter case and remove dirt completely.



PROCEDURE

Hide 23390 1.REMOVE FUEL FILTER ELEMENT ASSEMBLY

HINT:

Replacement of the fuel filter element assembly can be performed with the fuel filter installed to the fuel filter bracket.


a.
A339765

Detach the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe clamp.


b.
A339642N01
3.083,1 3.292,1.188 0.208,0.188 10 true 1 2.802,1.646 3.01,1.833 0.208,0.188 10 true 2

Disconnect the clamp and slide the lead wire as shown in the illustration to remove it.


c.
A339529

Disconnect the level warning switch connector.


d.
A339643

Slide the fuel filter assembly and lift it up.


e.
A339526

Connect a hose to the drain cock. Place the other end of the hose into a container under the drain cock.


f.

Loosen the drain cock to drain fuel.


g.

Tighten the drain cock by hand.


h.

Disconnect a hose from the drain cock.


i.
A339530

Disconnect the clogging switch connector.


j.
A339527

Using a screwdriver as a lever, loosen the fastener nut until it can be loosened by hand.


k.
A339528

Fully loosen the fastener nut by hand.


l.
A339532C01
2.208,1.083 2.656,1.083 true 2.729,1 2.948,1.198 0.219,0.198 10 false *1
*1 O-ring


To remove the fuel filter cap, pull up one side of the fuel filter cap, and then lift it off.


m.

Remove the fuel filter element assembly from the fuel filter case.


n.

Remove the O-ring from the fuel filter case.


Hide 23390 2.INSTALL FUEL FILTER ELEMENT ASSEMBLY

a.
A339533C01
0.271,1.042 0.542,1.042 true 1.698,0.448 1.823,0.448 1.823,0.448 2.104,0.75 true 0.052,0.958 0.25,1.125 0.198,0.167 10 true *1 1.51,0.354 1.688,0.521 0.177,0.167 10 true *2
*1 O-ring
*2 Fuel Filter Element Assembly


Install a new O-ring to the fuel filter case.


b.

Install the fuel filter element assembly to the fuel filter case.


c.
A339534

Align the mark on the fuel filter cap and the mark on the fuel filter case.


d.
A339535N01
2.844,3.844 3.031,4.031 0.188,0.188 10 true A

Push the fuel filter cap onto the fuel filter case by hand.

Standard clearance (A):

1.5 mm (0.0590 in.) or less


HINT:

The clearance between the fuel filter cap and fuel filter case should be even around the entire circumference of the fuel filter cap and fuel filter case.



e.
A339536N01
1.594,4.354 1.792,4.542 0.198,0.188 10 true A 3.26,3.208 3.417,3.365 0.156,0.156 10 true B

Turn the fastener nut until a "click" sound is heard.

HINT:

Just before the marks of the fuel filter case and nut align, the fastener nut will become more difficult to turn. Use a screwdriver as a lever to turn the fastener nut.



f.

Measure the distance between the marks on the fuel filter cap and fuel filter case, and the clearance between the fuel filter cap and fuel filter case.

Standard distance (A):

1.0 mm (0.0393 in.) or more


Standard clearance (B):

1.0 mm (0.0393 in.) or less



g.

Connect the clogging switch connector.


h.
A339669

Slide the fuel filter assembly to install it.


i.
A339641N01
2.792,1.646 3.01,1.823 0.219,0.177 10 true 1 3.083,0.969 3.302,1.146 0.219,0.177 10 true 2

Attach the clamp and slide the lead wire as shown in the illustration to install it.


j.
A339766C01
0.781,0.5 1.094,0.208 1.094,0.208 1.219,0.208 true 0.344,1.25 0.469,1.25 0.469,1.25 0.573,0.865 true 0.292,0.583 0.417,0.583 0.417,0.583 0.573,0.583 true 0.146,1.146 0.344,1.323 0.198,0.177 10 true *1 1.25,0.125 1.469,0.292 0.219,0.167 10 true *2 0.073,0.49 0.271,0.656 0.198,0.167 10 false *a
*1 No. 1 Fuel Hose
*2 No. 2 Fuel Pipe Clamp
*a Paint Mark


Attach the clamp and connect the No. 1 fuel hose to the No. 2 fuel pipe clamp.

HINT:

Make sure that the paint mark of the No. 1 fuel hose is positioned as shown in the illustration.



Hide 3.RESET FUEL SYSTEM WARNING LIGHT

a.

Turn the ignition switch to ON.


b.
A339670

After turning the ignition switch to ON, connect the level warning switch connector no sooner than 3 seconds have passed but no later than 60 seconds have passed.


c.

Check that the combination meter's fuel system warning light turns off.