The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0122 | Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open or short in VLU circuit ·
Open in VC circuit ·
ECM |
Comes on | DTC stored |
| P0123 | Throttle / Pedal Position Sensor / Switch "A" Circuit High Input | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open in E2 circuit ·
VC and VLU circuits are short-circuited ·
ECM |
Comes on | DTC stored |
If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- Intake booming noise
- Black smoke
- Lack of power
- Vibration at engine stop
- Turbo overspeed, turbo damage
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0122 | Ignition switch ON for 3 seconds or more |
| P0123 |
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C59-29 (VCVL) - C59-20 (EVLU) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C59-21 (VLU) - C59-20 (EVLU) | Ignition switch ON | 3.6 to 4.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P0122 or P0123 is output | B |
A
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
B
| *a | Front view of wire harness connector
(to Diesel Throttle Body Assembly) |
Disconnect the diesel throttle body assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Y1-5 (VC) - Y1-3 (E2) | Ignition switch ON | 4.5 to 5.5 V |
Reconnect the throttle position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y1-6 (VTA) - C59-21 (VLU) | Always | Below 1 Ω |
| Y1-3 (E2) - C59-20 (EVLU) | Always | Below 1 Ω |
| Y1-6 (VTA) or C59-21 (VLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Y1-3 (E2) or C59-20 (EVLU) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the diesel throttle body assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
| *a | Front view of wire harness connector
(to Diesel Throttle Body Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Y1-5 (VC) - Y1-6 (VTA) | Ignition switch off | No short or open circuit |
| Y1-6 (VTA) - Y1-3 (E2) |
Reconnect the diesel throttle body assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT