Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM33J0E _51 Engine / Hybrid System _038437 2GD-FTV ENGINE CONTROL _0201524 ECD SYSTEM(w/ DPF) D

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly or turbocharger nozzle vane control actuator is replaced, perform initialization


a.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.



CATALYST RECORD OF DPF THERMALDETERIORATION CLEAR FUNCTION


HINT:

When the exhaust manifold converter sub-assembly (DPF catalyst) is replaced, the catalyst record of DPF thermal deterioration stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Clear.

Powertrain > Engine > Utility
Tester Display
Catalyst Record Clear
50005 234 178

e.

Press "Next".


f.

Press "Exit".


g.

Enter the menu options in this order: Powertrain /Engine and ECT / Utility / DPF Deterioration Record Clear.

Powertrain > Engine > Utility
Tester Display
DPF Deterioration Record Clear
50005 234 253

h.

Press "Next".


i.

Press "Exit".



CRANK TIME COMPENSATION RESET FUNCTION


·

This procedure uses the GTS to perform "Crank Time Compensation Reset".

·

When replacing the timing rotor (engine assembly), perform "Crank Time Compensation Reset".


HINT:
·
A204035

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Crank Time Compensation Reset.

Powertrain > Engine and ECT > Utility
Tester Display
Crank Time Compensation Reset
50005 234 237

e.
A280989

When the first screen is displayed, check the vehicle condition and push "Next".


f.
A280984

When the screen indicating reset completion is displayed, push "Exit".



A/F SENSOR COMPENSATION RESET FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Compensation Reset".

·

When replacing the air fuel ratio sensor, replace the sensor and then perform "A/F Sensor Compensation Reset".


HINT:
·
A204038

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / A/F Sensor Compensation Reset.

Powertrain > Engine > Utility
Tester Display
A/F Sensor Compensation Reset
50005 234 238

e.
A295533

When the first screen is displayed, check the vehicle condition and press "Next".


f.
A295534

When the screen indicating reset completion is displayed, press "Exit".