Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner) › from 2015.11
RM33J0E _53 Suspension _038474 FRONT SUSPENSION _0187663 FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43360 1.INSTALL FRONT UPPER BALL JOINT

a.
C237641N01
2.063,0.219 1.719,0.219 false 1.719,0.219 0.99,0.813 false 0.99,2.406 0.792,2.406 0.792,2.406 0.729,2 false 2.094,0.146 2.5,0.333 0.406,0.188 10 false SST 1.073,2.323 1.479,2.51 0.406,0.188 10 false SST

Using SST and a press, press in a new front upper ball joint.

SST
09612-30012  
09223-00010  


b.

Using a snap ring expander, install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 2.INSTALL UPPER BALL JOINT DUST COVER

a.
C159213C15
2.5,0.938 2.5,1.719 false 1.896,1.25 1.99,1.25 false 1.427,1.25 1.521,1.25 false 2.5,0.938 2.063,0.938 true 2.5,1.458 2.208,1.458 false 2.208,1.458 1.969,1.26 false 1.427,1.25 0.979,1.25 false 0.75,1.167 0.958,1.313 0.208,0.146 10 false *a 2.406,1.75 2.615,1.896 0.208,0.146 10 false *a
*a MP grease


Pack the upper arm ball joint with MP grease.

Grease capacity:

8.0 g (0.282 oz.)



b.

Apply MP grease to the locations shown in the illustration.

NOTICE:

Do not apply MP grease to the tapered or threaded parts of the ball joint.



c.

Install a new upper ball joint dust cover to the front upper suspension arm assembly LH.


d.

Install a new dust cover set ring.


Hide 48632B 3.INSTALL FRONT UPPER SUSPENSION ARM BUSH LH

a.
C322825N01
1.073,0.417 0.552,0.667 0.552,0.667 0.917,0.771 false 0.26,0.594 0.719,0.792 0.458,0.198 10 false SST

Using SST and a press, press in a new front upper suspension arm bush LH.

SST
09316-10010  
09950-70010  (09951-07100)


Hide 48630 4.TEMPORARILY INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY LH

C322826C01
1.344,1.927 1.656,2.125 0.313,0.198 10 true *a
*a Nut


a.

Temporarily install the front upper suspension arm assembly LH and 2 retainers with the bolt and nut.

HINT:

Fix the nut in place and temporarily install the bolt.



b.

Install the front upper suspension arm assembly LH to the steering knuckle with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.

Install a new clip.


Hide 48810 5.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the steering knuckle with the nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 89543 6.CONNECT FRONT SPEED SENSOR LH

a.

Install the 2 bolts and connect the front speed sensor LH.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 7.INSTALL FRONT WHEEL

Hide 48630 9.TIGHTEN FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Tighten the bolt of the front upper suspension arm assembly LH.

Torque:
115 N*m (1173 kgf*cm, 85 ft.*lbf)

NOTICE:

Do not tighten the bolt.



Hide 10.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 11.PERFORM INITIALIZATION (w/ Automatic Headlight Beam Level Control System)

Hide 12.INSPECT AUTOMATIC LIGHT CONTROL SYSTEM (w/ Automatic Headlight Beam Level Control System)

Hide 13.INSPECT HEADLIGHT AIMING (w/ Automatic Headlight Beam Level Control System)