The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2 to use for adjusting the vehicle position on the display.
*1: for Automatic Transmission
*2: for Manual Transmission
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the lighting system (EXT) is operating normally before troubleshooting.
Enter the "Vehicle Signal Check Mode" screen.
Refer to check Vehicle Signal in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
Disconnect the navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G116-2 (REV) - Body ground | Ignition switch ON, shift lever in R | 11 to 14 V |
| G116-2 (REV) - Body ground | Ignition switch ON, shift lever any position other than in R | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
B
C
Disconnect the G116 navigation receiver assembly connector.
Disconnect the C24 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G116-2 (REV) - C24-1 (RL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C24-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
NG
Disconnect the G116 navigation receiver assembly connector.
Disconnect the C51 back-up light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G116-2 (REV) - C51-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back-up Light Switch Assembly) |
Disconnect the back-up light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C51-2 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for R151: Click hereDrivetrain>R151 MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
for R151F: Click hereDrivetrain>R151F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
for RC60 / RC61: Click hereDrivetrain>RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
for RC60F / RC61F: Click hereDrivetrain>RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
NG