Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.11
RM33J0E _56 Audio / Visual / Telematics _044808 NAVIGATION / MULTI INFO DISPLAY _0219999 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

E323581E03
5.313,0.802 5.927,1 0.615,0.198 10 false G118 5.313,1.563 5.927,1.76 0.615,0.198 10 false G118 5.302,2.396 5.917,2.594 0.615,0.198 10 false G116 5.302,3.198 5.917,3.396 0.615,0.198 10 false G118 5.74,0.802 6.354,1 0.615,0.198 10 false +B1 5.729,1.583 6.344,1.781 0.615,0.198 10 false ACC1 5.74,2.417 6.354,2.615 0.615,0.198 10 false IG 5.729,3.219 6.344,3.417 0.615,0.198 10 false GND1 5.552,3.854 6.813,4.229 1.26,0.375 10 false Navigation Receiver Assembly 5.417,2.969 5.667,3.167 0.25,0.198 10 false 7 5.406,2.177 5.656,2.375 0.25,0.198 10 false 1 5.438,1.354 5.688,1.552 0.25,0.198 10 false 3 5.427,0.573 5.677,0.771 0.25,0.198 10 false 4 3.229,0.958 3.844,1.156 0.615,0.198 10 false RADIO 3.417,1.719 4.031,1.917 0.615,0.198 10 false ACC 2.135,1.729 3.198,1.917 1.063,0.188 10 false SFT LOCK-ACC 1.677,0.771 3.104,0.979 1.427,0.208 10 false from Battery 0.771,1.531 2.438,1.74 1.667,0.208 10 false from ACC Relay 1.146,2.021 2.813,2.229 1.667,0.208 10 false from IG1 NO.1 Relay 1.229,2.406 2.49,2.583 1.26,0.177 10 false from Ignition Switch 4.552,2.573 5.177,2.771 0.625,0.198 10 false IG1 NO.4 3.177,1.927 3.792,2.125 0.615,0.198 10 false *1 3.177,2.281 3.792,2.479 0.615,0.198 10 false *2 0.333,3.875 3.115,4.115 2.781,0.24 10 false *1: w/ Smart Entry and Start System 0.333,4.26 2.802,4.479 2.469,0.219 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E280967C14
0.417,0.833 0.875,1.063 0.458,0.229 0.385,2.438 0.844,2.667 0.458,0.229 0.688,2.917 0.844,2.917 0.844,2.917 1.083,2.563 true 1.208,1.417 1.365,1.417 1.365,1.417 1.604,1.063 true 2.406,0.375 2.229,0.375 2.229,0.375 1.927,0.75 true 2.521,1.021 2.333,1.021 2.333,1.021 2.135,0.865 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.49,0.865 0.99,1.135 0.5,0.271 10 false G118 0.458,2.479 0.865,2.719 0.406,0.24 10 false G116 0.823,1.333 1.406,1.563 0.583,0.229 10 false GND1 2.458,0.313 3.021,0.531 0.563,0.219 10 false ACC1 2.563,0.948 3.125,1.167 0.563,0.219 10 false +B1 0.51,2.833 0.865,3.042 0.354,0.208 10 false IG
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G118-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G118-4 (+B1) - Body ground Always 11 to 14 V
G118-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
G116-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR