Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR › from 2015.11
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0199129 REAR SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR SPEED SENSOR (for 2WD)

a.

for RH:

C323035

i.

Install the rear speed sensor RH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Install the harness clamp with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




iii.

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



iv.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





b.

for LH:

C323034N01
3.125,2.083 3.281,2.281 0.156,0.198 10 true A 5.531,1.188 5.688,1.385 0.156,0.198 10 true B

i.

Install the rear speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Install the 2 harness clamps with the 2 bolts.

Torque:
Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt B : 32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




iii.

Attach the clamp.

NOTICE:

When attaching the clamp, do not twist the wire harness.



iv.

Connect the connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





Hide 2.INSTALL REAR SPEED SENSOR (for 4WD and Pre-Runner)

a.

for RH:

C323038

i.

Install the rear speed sensor RH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Install the harness clamp with the bolt.

Torque:
for TMT Made : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for TASA Made : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




iii.

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



iv.

Connect the connector and attach the clamp.

NOTICE:
·

Securely attach the connector.

·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





b.

for LH:

C323037N01
2.906,2.177 3.063,2.375 0.156,0.198 10 true A 5.5,1.51 5.656,1.708 0.156,0.198 10 true B

i.

Install the rear speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.




ii.

Install the 2 harness clamps with the 2 bolts.

Bolt A:
for TMT Made:

12.5 N*m (127 kgf*cm, 9 ft.*lbf)

for TASA Made:

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Bolt B:

32 N*m (326 kgf*cm, 24 ft.*lbf)


NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




iii.

Attach the 2 clamps.

NOTICE:

When attaching the clamp, do not twist the wire harness.



iv.

Connect the connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.