The following procedures are for BD22 (w/ Differential Lock).
41110
1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY
Secure the rear differential carrier assembly.
41204
2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
| *a | 36 mm (1.42 in.) |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| Runout | Maximum |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
If the runout is more than the maximum, replace the companion flange.
3.INSPECT DIFFERENTIAL RING GEAR BACKLASH
Using a dial indicator, measure the backlash of the differential ring gear.
0.13 to 0.20 mm (0.00512 to 0.00787 in.)
If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.
Perform the measurement at 3 or more positions around the circumference of the ring gear.
4.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.
If the result is not as specified, adjust the preload.
| Reduction Ratio | Specified Condition |
|---|---|
| 3.583 | 2.27 to 4.30 N*m (24 to 43 kgf*cm, 21 to 38 in.*lbf) |
| 3.909 | 2.25 to 4.24 N*m (23 to 43 kgf*cm, 20 to 37 in.*lbf) |
| 4.300 | 2.23 to 4.19 N*m (23 to 42 kgf*cm, 20 to 37 in.*lbf) |
| 4.555 | 2.21 to 4.16 N*m (23 to 42 kgf*cm, 20 to 36 in.*lbf) |
41204B
5.REMOVE REAR DRIVE PINION NUT
Using a chisel and hammer, stake the rear drive pinion nut.
| *a | Turn |
| *b | Hold |
Using SST to hold the companion flange in place, remove the rear drive pinion nut.
41204
6.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
| *a | Turn |
| *b | Hold |
Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
41201C
7.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
| *1 | Rear Differential Carrier Oil Seal |
| *2 | Rear Differential Drive Pinion Oil Slinger |
Using SST, remove the rear differential carrier oil seal.
41214
8.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Remove the rear differential drive pinion oil slinger from the differential drive pinion.
9.REMOVE WIRING HARNESS CONNECTOR
Remove the bolt and wiring harness connector.
Disconnect the connector.
10.REMOVE DIFFERENTIAL BEARING CAP
| *a | Matchmark |
Place matchmarks on the differential bearing cap and differential carrier.
Remove the 4 bolts and 2 differential bearing caps.
Remove the 2 plate washers.
| *a | LH Side (Ring Gear Side) | *b | RH Side (Differential Lock Coil Side) |
Put identification marks on the plate washers to show the location for installation (LH side (ring gear side) or RH side (differential lock coil side)), or keep them separate so that they can be distinguished.
Measure the thickness of each plate washers and note it.
41303E
11.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY
Remove the electronic differential lock case sub-assembly from the differential carrier.
Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.
84222
12.REMOVE NO. 1 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)
Remove the bolt and No. 1 transfer indicator switch (rear differential lock position switch).
13.REMOVE DIFFERENTIAL DRIVE PINION
Using a press, remove the differential drive pinion with rear differential drive pinion bearing spacer from the differential carrier.
Do not drop the differential drive pinion.
41231
14.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the rear differential drive pinion bearing spacer from the differential drive pinion.
41201A
15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner) from the differential drive pinion.
Do not drop the differential drive pinion.
If the differential drive pinion or differential ring gear is damaged, replace them as a set.
41201B
16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
Remove the rear drive pinion front tapered roller bearing (inner) from the differential carrier.
41201B
17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
| *1 | Rear Drive Pinion Front Tapered Roller Bearing (Outer) |
Using SST, remove the rear drive pinion front tapered roller bearing (outer) from the differential carrier.
41115
18.REMOVE DIFFERENTIAL OIL STORAGE RING
| *1 | Differential Oil Storage Ring |
Using SST and a hammer, tap out the differential oil storage ring from the differential carrier.
41201A
19.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer) and adjusting shim from the differential carrier.
If the bearing is damaged during removal, replace it.
20.REMOVE DIFFERENTIAL RING GEAR
| *a | Matchmark |
Place matchmarks on the differential ring gear and differential case.
Remove the 12 differential ring gear set bolts.
Using a plastic-faced hammer, tap on the differential ring gear to remove it from the differential case.
Do not damage the position plate when removing the ring gear.
21.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT
If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.
Install the rear differential case bearings (outer) to the electronic differential lock case sub-assembly.
Install the electronic differential lock case sub-assembly to the differential carrier.
Install the 2 plate washers.
Install the 2 differential bearing caps to the differential carrier with the 4 bolts.
| *a | 92 mm (3.62 in.) |
Using a dial indicator, measure the electronic differential case runout.
0.07 mm (0.00276 in.)
Remove the 4 bolts and 2 differential bearing caps.
Remove the 2 plate washers.
Remove the electronic differential lock case sub-assembly.
Remove the rear differential case bearings (outer).
41301A
22.REMOVE REAR DIFFERENTIAL CASE BEARING
| *a | Turn |
| *b | Hold |
for LH Side (Ring Gear Side):
Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.
Do not remove the case bearings when not replacing the electronic differential lock case sub-assembly.
for RH Side (Differential Lock Coil Side):
| *a | Turn |
| *b | Hold |
Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.
Do not remove the case bearings when not replacing the electronic differential lock case sub-assembly.
41367
23.REMOVE DIFFERENTIAL SOLENOID WASHER
Tighten the 2 SST nuts evenly and remove the differential solenoid washer from the electronic differential lock case sub-assembly.
41451H
24.REMOVE DIFFERENTIAL LOCK COIL
Remove the differential lock coil from the electronic differential lock case sub-assembly.
25.REMOVE DIFFERENTIAL LOCK PLUNGER
Remove the differential lock plunger from the rear differential case sub-assembly.
41302
26.DISASSEMBLE REAR DIFFERENTIAL CASE SUB-ASSEMBLY
Remove the 2 screws.
| *1 | Differential Case LH |
| *2 | Differential Case RH |
Remove the differential case LH from the differential case RH.
Remove the differential side gear and rear No. 1 differential side gear thrust washer from the differential case LH.
Remove the 2 rear differential pinion shaft pins.
| *1 | Differential Side Gear (Dog Clutch) |
| *2 | Rear No. 2 Differential Side Gear Thrust Washer |
| *3 | Rear No. 3 Differential Side Gear Thrust Washer |
| *4 | Differential Pinion |
| *5 | Rear Differential Pinion Thrust Washer |
| *6 | Rear Differential Pinion Shaft |
| *7 | Rear No. 2 Differential Pinion Shaft |
| *8 | Differential Lock Spring |
Remove the following parts from the differential case RH.
Differential side gear (Dog clutch)
Rear No. 2 differential side gear thrust washer
Rear No. 3 differential side gear thrust washer
Differential pinion (4 pieces)
Rear differential pinion thrust washer (4 pieces)
Rear differential pinion shaft
Rear No. 2 differential pinion shaft (2 pieces)
Differential lock spring
41474A
27.REMOVE DIFFERENTIAL LOCK POSITION PLATE
Using a T25 ''TORX'' socket wrench, remove the 3 screws from the differential lock position plate.
| *1 | Differential Lock Position Plate |
| *2 | Differential Lock Cam Ring |
Remove the differential lock position plate from the differential case RH.
41433A
28.REMOVE DIFFERENTIAL LOCK CAM RING
Remove the differential lock cam ring from the differential case RH.
29.INSPECT DIFFERENTIAL GEAR KIT
Check that the differential pinion and differential side gear are not damaged.
If the differential pinion or differential side gear is damaged, replace the differential gear kit.
30.INSPECT DIFFERENTIAL CASE
Check that the differential case is not damaged.
If the differential case is damaged, replace it.