Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.11
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0192391 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the downhill assist control* or hill-start assist control operating signal from the skid control ECU (brake actuator assembly), the relay contact turns on and the stop light comes on.

*: w/ Downhill Assist Control


DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either of the following is detected:
1.

When the voltage at the +BS terminal is 9.5 V or higher and the stop light control relay drive output (STPO) is on, a signal has not been input to the STP terminal for 2 seconds or more.

2.

When the voltage at the +BS terminal is 9.5 V or higher and the stop light control relay drive output (STPO) is off, the signal at the STP is different from the input signal at the STP2 for 2 seconds or more.


·

IG1 NO. 3 fuse

·

STOP fuse

·

Stop light switch circuit

·

Stop light control relay (STOP/CDS FAN Relay)

·

Stop light control relay circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C325619E11
0.792,1.094 2.792,1.417 2,0.323 10 false Stop Light Switch Assembly 2.417,3.26 4.156,3.667 1.74,0.406 10 false Stop Light Control Relay (STOP/CDS FAN Relay) 4.135,4.458 5.542,4.875 1.406,0.417 10 false to Stop Light Circuit 2.26,4.073 3.667,4.49 1.406,0.417 10 false from IG Circuit 1.063,4.26 2.469,4.677 1.406,0.417 10 false IG1 NO. 3 5.542,4.906 7.104,5.333 1.563,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 5.292,4.906 5.604,5.146 0.313,0.24 10 false A4 0.604,5.281 1.26,5.521 0.656,0.24 10 false STOP 1.51,5.115 2.917,5.531 1.406,0.417 10 false from Battery 0.479,1.104 0.792,1.344 0.313,0.24 10 false A35 5.969,0.604 6.458,0.896 0.49,0.292 10 false STP2 6.021,2.198 6.51,2.49 0.49,0.292 10 false STP 6,2.865 6.49,3.156 0.49,0.292 10 false STPO 0.771,0.438 0.906,0.635 0.135,0.198 10 false 2 5.708,2.031 5.948,2.229 0.24,0.198 10 false 35 5.708,2.688 5.948,2.885 0.24,0.198 10 false 26 3.688,2.688 3.823,2.885 0.135,0.198 10 false 2 2.458,2.677 2.594,2.875 0.135,0.198 10 false 1 3.688,2.021 3.823,2.219 0.135,0.198 10 false 3 2.469,2.021 2.604,2.219 0.135,0.198 10 false 5 2.896,1.615 3.031,1.813 0.135,0.198 10 false 4 2.135,0.438 2.271,0.635 0.135,0.198 10 false 1 5.74,0.427 5.979,0.625 0.24,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off


Result:
Result
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Turn the ignition switch off.


c.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.
C306843C64
1.531,0.104 1.896,0.333 0.365,0.229 2.708,1.844 2.708,1.667 2.708,1.667 2.208,1.323 true 2.604,1.875 2.917,2.073 0.313,0.198 10 false STP 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.615,0.135 2.073,0.333 0.458,0.198 10 false A4
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V


Result:
Result
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C306843C65
1.531,0.083 1.865,0.313 0.333,0.229 1.104,0.229 1.333,0.229 1.333,0.229 1.646,0.854 true 0.75,0.156 1.365,0.354 0.615,0.198 10 false STP2 1.604,0.115 2.063,0.313 0.458,0.198 10 false A4 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-7 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V


Result:
Result
OK
NG




OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (STOP/CDS FAN Relay) Relay ON/OFF Stop lights come on
Vehicle condition: Vehicle stopped
f.

While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (STOP/CDS FAN Relay) output ON or OFF OFF: Relay output off (Stop lights off)
ON: Relay output on (Stop lights on)
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291
Result:
Result Proceed to
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B



A

5.RECONFIRM DTC

B

6.INSPECT STOP LIGHT CONTROL RELAY (STOP/CDS FAN RELAY)
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1380 is not output
DTC C1380 is output




DTC C1380 is not output

DTC C1380 is output

6.INSPECT STOP LIGHT CONTROL RELAY (STOP/CDS FAN RELAY)
a.

Turn the ignition switch off.


b.

Remove the stop light control relay (STOP/CDS FAN Relay) from the engine room relay block and junction block.


c.

Inspect the stop light control relay (STOP/CDS FAN Relay).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>RELAY>ON-VEHICLE INSPECTION

OK:

The stop light control relay (STOP/CDS FAN Relay) is normal.


Result:
Result
OK
NG




OK

7.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE TERMINAL)

NG

REPLACE STOP LIGHT CONTROL RELAY (STOP/CDS FAN RELAY)

7.CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE TERMINAL)
a.
C325044C01
0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Component without Stop Light Control Relay (STOP/CDS FAN Relay)
(Engine Room Relay Block and Junction Block)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 - Body ground Always 11 to 14 V
1 - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)
a.

Install the stop light control relay (STOP/CDS FAN Relay).


b.

Make sure that there is no looseness in the locking part and connecting part of the connector.


c.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

Turn the ignition switch to ON.


e.
C306843C66
1.531,0.083 1.865,0.313 0.333,0.229 0.438,1.906 0.667,1.906 0.667,1.906 0.875,1.333 true 0.042,1.823 0.656,2.021 0.615,0.198 10 false STPO 1.615,0.115 2.073,0.313 0.458,0.198 10 false A4 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-26 (STPO) - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)