Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2015.11–2016.07
RM33J0E _57 Power Source / Network _038493 NETWORKING _0190453 CAN COMMUNICATION SYSTEM(for LHD) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 1 CAN Junction Connector

C343209C37
0.833,0.771 1.333,1.021 0.5,0.25 2.188,0.646 2.375,0.646 2.375,0.646 2.635,0.885 true 2.375,0.438 2.563,0.438 2.563,0.438 2.813,0.865 true 2.625,0.26 2.813,0.26 2.813,0.26 3.021,0.865 true 2.865,0.135 3.052,0.135 3.052,0.135 3.208,0.854 true 2.24,1.198 2.427,1.198 2.427,1.198 2.656,1.042 true 2.354,1.406 2.542,1.406 2.542,1.406 2.823,1.031 true 2.531,1.573 2.719,1.573 2.719,1.573 3.01,1.021 true 3.177,1.573 3.031,1.573 3.031,1.573 3.208,1.01 true 3.875,0.125 3.688,0.125 3.688,0.125 3.427,0.854 true 4.896,0.635 4.708,0.635 4.708,0.635 4.125,0.885 true 4.76,0.354 4.573,0.354 4.573,0.354 3.729,0.885 true 4.885,1.292 4.698,1.292 4.698,1.292 4.156,1.031 true 4.698,1.469 4.51,1.469 4.51,1.469 3.76,1.01 true 4.115,1.646 3.906,1.646 3.906,1.646 3.396,1.031 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.615,0.552 2.229,0.76 0.615,0.208 10 false CANH*b 1.823,0.333 2.438,0.542 0.615,0.208 10 false CANH*c 2.073,0.156 2.688,0.365 0.615,0.208 10 false CANH*d 2.302,0.01 2.917,0.219 0.615,0.208 10 false CANH*e 3.938,0.031 4.552,0.24 0.615,0.208 10 false CANH*f 4.813,0.24 5.427,0.448 0.615,0.208 10 false CANH*g 4.958,0.521 5.573,0.729 0.615,0.208 10 false CANH*h 1.688,1.063 2.302,1.271 0.615,0.208 10 false CANL*b 1.813,1.302 2.427,1.51 0.615,0.208 10 false CANL*c 1.99,1.469 2.604,1.677 0.615,0.208 10 false CANL*d 3.219,1.458 3.833,1.667 0.615,0.208 10 false CANL*e 4.146,1.531 4.76,1.74 0.615,0.208 10 false CANL*f 4.938,1.156 5.552,1.365 0.615,0.208 10 false CANL*h 4.76,1.365 5.375,1.573 0.615,0.208 10 false CANL*g 0.958,0.792 1.417,0.99 0.458,0.198 10 false G67
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for Brake Actuator Assembly (Skid Control ECU)
*c for Airbag Sensor Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC)
*e for DLC3 *f for Combination Meter Assembly
*g for No. 2 CAN Junction Connector *h for Headlight Leveling ECU Assembly (for LED Headlight)


No. 1 CAN Junction Connector Wiring Color Connect to

*1: w/ VSC

*2: for LED Headlight

G67-1 (CANH) B Brake actuator assembly (skid control ECU)
G67-11 (CANL) W
G67-2 (CANH) Y Airbag sensor assembly
G67-12 (CANL) W
G67-3 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)*1
G67-13 (CANL) W
G67-4 (CANH) L DLC3
G67-14 (CANL) W
G67-5 (CANH) SB Combination meter assembly
G67-15 (CANL) W
G67-6 (CANH) LG No. 2 CAN junction connector
G67-16 (CANL) W
G67-8 (CANH) V Headlight leveling ECU assembly*2
G67-18 (CANL) W


b.

No. 2 CAN Junction Connector

C300828C69
0.833,0.74 1.219,1 0.385,0.26 2.969,0.854 2.188,0.542 2.188,0.542 2.031,0.542 true 3.01,1.01 2.135,1.26 2.135,1.26 2.01,1.26 true 3.75,0.823 4.854,0.188 4.854,0.188 5,0.188 true 3.74,1.021 4.604,1.625 4.604,1.625 4.76,1.625 true 3.969,0.844 4.906,0.458 4.906,0.458 5.094,0.458 true 3.979,1.031 4.844,1.438 4.844,1.438 5,1.438 true 3.177,0.854 2.406,0.333 2.406,0.333 2.25,0.333 true 3.375,0.865 2.667,0.146 2.667,0.146 2.51,0.146 true 3.219,1.042 2.406,1.469 2.406,1.469 2.281,1.469 true 3.375,1.021 2.74,1.677 2.74,1.677 2.615,1.677 true 4.552,0.865 5.021,0.708 5.021,0.708 5.208,0.708 true 4.542,1.021 4.979,1.229 4.979,1.229 5.135,1.229 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 1.688,0.25 2.313,0.563 0.625,0.313 10 false CANH*c 1.938,0.063 2.542,0.281 0.604,0.219 10 false CANH*d 5.063,0.125 5.729,0.396 0.667,0.271 10 false CANH*e 1.719,1.375 2.344,1.604 0.625,0.229 10 false CANL*c 2.073,1.583 2.688,1.75 0.615,0.167 10 false CANL*d 4.833,1.552 5.448,1.74 0.615,0.188 10 false CANL*e 5.156,0.396 5.781,0.646 0.625,0.25 10 false CANH*f 5.083,1.365 5.74,1.573 0.656,0.208 10 false CANL*f 1.448,0.479 2.146,0.76 0.698,0.281 10 false CANH*b 1.458,1.167 2.042,1.344 0.583,0.177 10 false CANL*b 0.906,0.781 1.302,1.083 0.396,0.302 10 false G68 5.25,0.625 5.875,0.875 0.625,0.25 10 false CANH*g 5.198,1.146 5.854,1.354 0.656,0.208 10 false CANL*g
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for Certification ECU (Smart Key ECU Assembly) (w/ Smart Entry and Start System)
*c for 4 Wheel Drive Control ECU (for 4WD) *d for ECM
*e for No. 1 CAN Junction Connector *f
·

for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

·

for Navigation Receiver Assembly (w/ Navigation System)


*g for Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System) - -


No. 2 CAN Junction Connector Wiring Color Connect to

*1: w/ Smart Entry and Start System

*2: for 4WD

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Navigation System

*5: for Automatic Air Conditioning System

G68-3 (CANH) G Certification ECU (smart key ECU assembly)*1
G68-13 (CANL) W
G68-4 (CANH) R 4 wheel drive control ECU*2
G68-14 (CANL) W
G68-5 (CANH) B ECM
G68-15 (CANL) W
G68-6 (CANH) LG No. 1 CAN junction connector
G68-16 (CANL) W
G68-7 (CANH) V
·

Radio and display receiver assembly*3

·

Navigation receiver assembly*4


G68-17 (CANL) W
G68-10 (CANH) GR Air conditioning amplifier assembly*5
G68-20 (CANL) W



CHECK DLC3


a.
C253362C15
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.292,1.052 0.75,1.25 0.458,0.198 10 false G8 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click here

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G8-6 (CANH) - G8-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-14 (CANL) - G8-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-6 (CANH) - G8-16 (BAT) L - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-14 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2TR-FE)


C317086E02
1.521,0.51 1.979,0.781 0.458,0.271 2.677,0.51 3.135,0.781 0.458,0.271 3.896,0.51 4.354,0.781 0.458,0.271 5,0.51 5.458,0.781 0.458,0.271 0.76,0.813 0.938,0.813 0.938,0.813 1.854,1.156 true 5.844,0.76 5.729,0.76 5.729,0.76 5.375,1.146 true 3.531,2.135 3.708,2.135 3.708,2.135 3.813,1.354 true 4.365,2.167 4.25,2.167 4.25,2.167 3.917,1.354 true 1.635,0.563 2.094,0.76 0.458,0.198 10 false C52 2.792,0.573 3.25,0.771 0.458,0.198 10 false C53 3.99,0.573 4.448,0.771 0.458,0.198 10 false G45 5.104,0.573 5.563,0.771 0.458,0.198 10 false G46 4.448,2.083 5.063,2.281 0.615,0.198 10 false CANH 3.125,2.073 3.74,2.271 0.615,0.198 10 false CANL 5.927,0.667 6.542,0.865 0.615,0.198 10 false BATT 0.542,0.729 1.156,0.927 0.615,0.198 10 false E1

a.

Disconnect the ECM connectors.

C317087C04
0.875,0.51 1.302,0.771 0.427,0.26 3.375,0.521 3.802,0.781 0.427,0.26 5.917,0.531 6.344,0.792 0.427,0.26 0.542,0.875 0.677,0.875 0.677,0.875 0.896,1.396 true 4.354,0.906 4.219,0.906 4.219,0.906 3.948,1.563 true 3.031,0.875 3.167,0.875 3.167,0.875 3.833,1.573 true 5.531,0.906 5.667,0.906 5.667,0.906 5.969,1.385 true 0.958,0.552 1.417,0.75 0.458,0.198 10 false G46 3.469,0.573 3.927,0.771 0.458,0.198 10 false G45 6.01,0.573 6.469,0.771 0.458,0.198 10 false C52 2.604,0.802 3.219,1 0.615,0.198 10 false CANH 4.448,0.813 5.063,1.01 0.615,0.198 10 false CANL 0.167,0.802 0.781,1 0.615,0.198 10 false BATT 5.313,0.833 5.927,1.031 0.615,0.198 10 false E1 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G45-13 (CANH) - G45-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G45-13 (CANH) - C52-3 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G45-14 (CANL) - C52-3 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G45-13 (CANH) - G46-3 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G45-14 (CANL) - G46-3 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 1GD-FTV, 2GD-FTV)


A340466E10
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 3.906,2.125 4.052,2.125 4.052,2.125 4.51,1.198 true 6.344,2.104 6.5,2.104 6.5,2.104 6.74,1.219 true 4.979,2.031 5.125,2.031 5.125,2.031 5.667,1.49 true 5.302,2.375 5.448,2.375 5.448,2.375 5.698,1.646 true 1.833,0.469 2.146,0.667 0.313,0.198 10 false C58 0.615,0.469 0.927,0.667 0.313,0.198 10 false C57 2.938,0.469 3.25,0.667 0.313,0.198 10 false C59 3.979,0.469 4.292,0.667 0.313,0.198 10 false C60 5.094,0.469 5.406,0.667 0.313,0.198 10 false G85 6.25,0.458 6.563,0.656 0.313,0.198 10 false G86 5.948,2.031 6.333,2.229 0.385,0.198 10 false BATT 3.667,2.052 3.917,2.26 0.25,0.208 10 false E1 4.552,1.958 4.979,2.146 0.427,0.188 10 false CANH 4.865,2.302 5.302,2.49 0.438,0.188 10 false CANL

a.

Disconnect the ECM connectors.

C317088C04
1,0.448 1.448,0.719 0.448,0.271 3.25,0.438 3.698,0.708 0.448,0.271 5.552,0.406 6,0.677 0.448,0.271 0.521,0.896 0.656,0.896 0.656,0.896 0.698,1.396 true 2.667,0.979 2.802,0.979 2.802,0.979 2.927,1.688 true 4.917,0.865 5.052,0.865 5.052,0.865 5.219,1.406 true 2.625,2.323 2.76,2.323 2.76,2.323 2.927,1.906 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.094,0.51 1.552,0.708 0.458,0.198 10 false G86 3.344,0.49 3.802,0.688 0.458,0.198 10 false G85 5.656,0.469 6.115,0.667 0.458,0.198 10 false C60 0.125,0.823 0.531,1.031 0.406,0.208 10 false BATT 4.677,0.781 4.958,0.969 0.281,0.188 10 false E1 2.219,0.906 2.625,1.115 0.406,0.208 10 false CANH 2.219,2.25 2.625,2.458 0.406,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G85-17 (CANH) - C60-1 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G85-28 (CANL) - C60-1 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G85-17 (CANH) - G86-1 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G85-28 (CANL) - G86-1 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 1KD-FTV, 2KD-FTV)


C317086E03
1.521,0.51 1.979,0.781 0.458,0.271 2.677,0.51 3.135,0.781 0.458,0.271 3.896,0.51 4.354,0.781 0.458,0.271 5,0.51 5.458,0.781 0.458,0.271 1.5,2.156 1.677,2.156 1.677,2.156 2.417,1.177 true 5.292,2.135 5.177,2.135 5.177,2.135 4.344,1.198 true 3.531,2.135 3.708,2.135 3.708,2.135 3.896,1.49 true 4.365,2.167 4.25,2.167 4.25,2.167 4.021,1.49 true 1.635,0.563 2.094,0.76 0.458,0.198 10 false C55 2.792,0.573 3.25,0.771 0.458,0.198 10 false C56 3.99,0.573 4.448,0.771 0.458,0.198 10 false G83 5.104,0.573 5.563,0.771 0.458,0.198 10 false G84 3.125,2.073 3.74,2.271 0.615,0.198 10 false CANH 4.427,2.083 5.042,2.281 0.615,0.198 10 false CANL 5.354,2.052 5.969,2.25 0.615,0.198 10 false BATT 1.281,2.083 1.896,2.281 0.615,0.198 10 false E1

a.

Disconnect the ECM connectors.

C329287C01
5.063,0.24 5.521,0.552 0.458,0.313 1.677,0.229 2.135,0.542 0.458,0.313 5.896,1.135 6.073,0.667 6.073,0.667 6.208,0.667 true 1.135,0.719 1.26,0.719 1.26,0.719 1.656,1.115 true 2.188,1.469 2.458,2.208 2.458,2.208 2.594,2.208 true 1.667,2.188 1.792,2.188 1.792,2.188 2.063,1.5 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.781,0.302 2.24,0.5 0.458,0.198 10 false G83 5.188,0.323 5.646,0.521 0.458,0.198 10 false C56 0.729,0.646 1.344,0.844 0.615,0.198 10 false BATT 6.281,0.583 6.896,0.781 0.615,0.198 10 false E1 2.667,2.125 3.281,2.323 0.615,0.198 10 false CANH 1.26,2.115 1.875,2.313 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G83-24 (CANH) - G83-23 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G83-24 (CANH) - C56-7 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G83-23 (CANL) - C56-7 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G83-24 (CANH) - G83-2 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G83-23 (CANL) - G83-2 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130E31
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.906,1.208 2.677,1.646 2.677,1.646 2.552,1.646 true 3.042,1.208 3.229,1.615 3.229,1.615 3.417,1.615 true 4,1.135 4.844,0.417 4.844,0.417 4.927,0.417 true 3.479,0.323 3.76,0.49 0.281,0.167 10 false G9 5,1.479 5.26,1.667 0.26,0.188 10 false B 2.135,1.563 2.552,1.729 0.417,0.167 10 false CANH 3.448,1.531 3.875,1.688 0.427,0.156 10 false CANL 5.01,0.344 5.313,0.521 0.302,0.177 10 false EP

a.
C240157C58
1.531,0.146 1.969,0.458 0.438,0.313 1.396,1.25 2.104,1.781 2.104,1.781 2.333,1.781 true 1.302,1.24 1.042,1.865 1.042,1.865 0.802,1.865 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 2.635,0.552 2.479,0.552 2.479,0.552 2.052,1.198 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false G9 0.385,1.802 0.802,2 0.417,0.198 10 false CANH 2.375,1.708 2.854,1.906 0.479,0.198 10 false CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 false B 2.698,0.469 3.063,0.729 0.365,0.26 10 false EP
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G9-36 (CANH) - G9-27 (EP) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G9-35 (CANL) - G9-27 (EP) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G9-36 (CANH) - G9-21 (B) SB - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G9-35 (CANL) - G9-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


Type A:
C231510E04
3.021,0.073 3.375,0.302 0.354,0.229 4.167,0.083 4.521,0.313 0.354,0.229 3.49,0.979 5.021,0.49 5.021,0.49 5.125,0.49 true 1.75,0.844 1.896,0.844 1.896,0.844 3.208,1.208 true 3.625,1.198 5.135,0.875 5.135,0.875 5.24,0.875 true 3.073,0.104 3.531,0.302 0.458,0.198 10 false G42 4.229,0.115 4.688,0.313 0.458,0.198 10 false N15 5.219,0.406 5.833,0.604 0.615,0.198 10 false CANH 5.313,0.802 5.927,1 0.615,0.198 10 false CANL 1.51,0.771 2.125,0.969 0.615,0.198 10 false E1

Type B:
C123353E86
2.594,0.688 2.979,0.917 0.385,0.229 3.854,0.688 4.24,0.917 0.385,0.229 4.719,0.677 5.104,0.906 0.385,0.229 3.365,2.01 3.688,2.479 3.688,2.479 3.823,2.479 true 2.802,2.021 2.271,2.385 2.271,2.385 2.135,2.385 true 3.146,1.781 2.927,2.542 2.927,2.542 2.792,2.542 true 2.646,0.719 3.031,0.948 0.385,0.229 10 false G42 3.927,0.719 4.271,0.958 0.344,0.24 10 false N14 4.802,0.719 5.208,0.979 0.406,0.26 10 false N15 1.927,2.313 2.24,2.51 0.313,0.198 10 false E1 3.896,2.385 4.521,2.615 0.625,0.229 10 false CANL 2.365,2.458 2.875,2.656 0.51,0.198 10 false CANH

a.
C227529C07
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.479,2.573 0.823,2.781 0.344,0.208 10 false G8 0.417,1 0.76,1.208 0.344,0.208 10 false G42 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G42-13 (CANH) - G42-22 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G42-13 (CANH) - G42-25 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G42-22 (CANL) - G42-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G42-13 (CANH) - G8-16 (BAT) Y - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G42-22 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC)


C306841E03
3.302,0.156 3.719,0.406 0.417,0.25 1.49,0.365 1.708,0.365 1.708,0.365 2.885,1.073 true 1.521,2.292 1.719,2.292 1.719,2.292 2.885,1.385 true 0.896,0.708 1.115,0.708 1.115,0.708 2.104,1.104 true 5.625,2.208 5.448,2.208 5.448,2.208 4.979,1.677 true 3.406,0.219 3.865,0.417 0.458,0.198 10 false A4 1.115,2.25 1.625,2.396 0.51,0.146 10 false CANH 1.083,0.323 1.594,0.469 0.51,0.146 10 false CANL 0.625,0.646 0.906,0.854 0.281,0.208 10 false BM 5.708,2.125 6.219,2.271 0.51,0.146 10 false GND1

a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C306842C08
3.448,0.292 3.781,0.573 0.333,0.281 3.938,1.115 4.708,0.656 4.708,0.656 4.885,0.656 true 4.375,1.188 4.906,1.875 4.906,1.875 5.083,1.875 true 3.958,1.281 4.729,2.333 4.729,2.333 4.906,2.333 true 2.771,1.417 2.406,2.063 2.406,2.063 2.208,2.063 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 3.531,0.354 3.99,0.552 0.458,0.198 10 false A4 4.938,0.583 5.552,0.781 0.615,0.198 10 false CANL 4.99,2.25 5.604,2.448 0.615,0.198 10 false CANH 5.125,1.802 5.74,2 0.615,0.198 10 false BM 1.792,1.979 2.406,2.177 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A4-22 (CANH) - A4-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-10 (CANL) - A4-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-22 (CANH) - A4-13 (BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A4-10 (CANL) - A4-13 (BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC)


C197053E24
1.458,0.083 1.875,0.344 0.417,0.26 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 2.375,1.417 2.635,1.844 2.635,1.844 2.802,1.844 true 2.344,1.604 1.969,2.042 1.969,2.042 2.229,2.042 true 2.583,0.917 2.75,0.333 2.75,0.333 2.917,0.333 true 0.719,1.479 0.375,1.979 0.375,1.979 0.573,1.979 true 2.271,1.958 2.74,2.135 0.469,0.177 10 false CANH 2.844,1.771 3.313,1.948 0.469,0.177 10 false CANL 2.948,0.26 3.365,0.427 0.417,0.167 10 false GND1 0.625,1.906 1.177,2.083 0.552,0.177 10 false +BM 1.583,0.146 1.896,0.313 0.313,0.167 10 false A3

a.
C317089C01
1.563,0.156 2.031,0.406 0.469,0.25 0.521,0.594 0.667,0.594 0.667,0.594 1.156,1.031 true 0.5,1.031 0.635,1.031 0.635,1.031 1.448,1.26 true 0.625,1.927 0.771,1.927 0.771,1.927 1.458,1.365 true 2.135,1.979 2.281,1.979 2.281,1.979 2.469,1.354 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.198,1.844 0.625,2.042 0.427,0.198 10 false CANH 0.115,0.958 0.5,1.167 0.385,0.208 10 false CANL 1.792,1.906 2.135,2.125 0.344,0.219 10 false +BM 0.135,0.531 0.573,0.74 0.438,0.208 10 false GND1 1.729,0.198 2.042,0.396 0.313,0.198 10 false A3
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A3-25 (CANH) - A3-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A3-25 (CANH) - A3-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-14 (CANL) - A3-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-25 (CANH) - A3-24 (+BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A3-14 (CANL) - A3-24 (+BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC)


C228050E06
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 false G21 2.833,0.896 3.24,1.052 0.406,0.156 10 false ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 false CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 false CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 false BAT

a.
C277459C19
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G21 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G21-3 (CANH) - G21-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G21-3 (CANH) - G21-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G21-2 (CANL) - G21-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G21-3 (CANH) - G21-5 (BAT) BE - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G21-2 (CANL) - G21-5 (BAT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


B391999E05
2.281,0.583 2.781,0.833 0.5,0.25 4.052,0.583 4.552,0.833 0.5,0.25 1.646,2.094 1.781,2.094 1.781,2.094 2.052,1.365 true 2.677,2.094 2.813,2.094 2.813,2.094 3.042,1.365 true 3.563,0.688 3.698,0.688 3.698,0.688 3.667,1.323 true 4.229,2.104 4.104,2.104 4.104,2.104 3.698,1.427 true 2.396,0.635 2.854,0.833 0.458,0.198 10 false G69 4.167,0.635 4.625,0.833 0.458,0.198 10 false G70 4.292,2.021 4.906,2.219 0.615,0.198 10 false CANH 3.125,0.625 3.74,0.823 0.615,0.198 10 false CANL 2.427,2.021 3.042,2.219 0.615,0.198 10 false +B 1.458,2.031 2.073,2.229 0.615,0.198 10 false E

a.

Disconnect the certification ECU (smart key ECU assembly) connectors.

E277246C07
1.875,0.667 2.292,0.917 0.417,0.25 4.74,0.667 5.156,0.917 0.417,0.25 1.229,1.365 0.865,2.167 0.865,2.167 0.719,2.167 true 2.896,1.333 3.135,2.208 3.135,2.208 3.271,2.208 true 6.333,0.854 6.198,0.854 6.198,0.854 6.063,1.313 true 6.031,1.49 6.177,2.188 6.177,2.188 6.333,2.188 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 0.469,2.104 0.729,2.302 0.26,0.198 10 false +B 3.354,2.135 3.667,2.333 0.313,0.198 10 false E 6.417,0.781 6.813,0.979 0.396,0.198 10 false CANL 6.396,2.115 6.885,2.313 0.49,0.198 10 false CANH 1.969,0.708 2.427,0.906 0.458,0.198 10 false G69 4.844,0.708 5.302,0.906 0.458,0.198 10 false G70
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G70-40 (CANH) - G70-18 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G70-40 (CANH) - G69-10 (E) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-18 (CANL) - G69-10 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-40 (CANH) - G69-1 (+B) G - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G70-18 (CANL) - G69-1 (+B) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


E317641E03
3.99,0.458 4.438,0.719 0.448,0.26 2.271,2.01 2.719,2.271 0.448,0.26 1.604,2.271 1.75,2.271 1.75,2.271 2.083,2.573 true 2.979,3.333 2.823,3.333 2.823,3.333 2.573,2.792 true 4.406,1.667 4.25,1.667 4.25,1.667 4.042,1.115 true 3.417,1.656 3.563,1.656 3.563,1.656 3.917,1.115 true 4.073,0.521 4.594,0.698 0.521,0.177 10 false G37 2.365,2.063 2.708,2.24 0.344,0.177 10 false G40 3.042,3.26 3.656,3.458 0.615,0.198 10 false GND1 1.302,2.188 1.917,2.385 0.615,0.198 10 false +B1 4.469,1.573 5.083,1.771 0.615,0.198 10 false CANH 3,1.583 3.615,1.781 0.615,0.198 10 false CANL

a.
C277477C21
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.594,0.281 2.052,0.479 0.458,0.198 10 false G40 1.563,1.865 2.021,2.063 0.458,0.198 10 false G37 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-9 (CANH) - G37-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G37-9 (CANH) - G40-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-10 (CANL) - G40-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-9 (CANH) - G40-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G37-10 (CANL) - G40-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


C297912E09
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 5,0.802 5.302,1.333 5.302,1.333 5.469,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.49,0.167 2.104,0.365 0.615,0.198 10 false G118 4.99,0.146 5.604,0.344 0.615,0.198 10 false G116 5.521,1.229 6.135,1.427 0.615,0.198 10 false CANH 4.052,1.26 4.667,1.458 0.615,0.198 10 false CANL 2.208,1.177 2.823,1.375 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C29
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.552,0.271 2.01,0.469 0.458,0.198 10 false G118 1.521,1.854 1.979,2.052 0.458,0.198 10 false G116 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G116-9 (CANH) - G116-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G116-9 (CANH) - G118-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G116-10 (CANL) - G118-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G116-9 (CANH) - G118-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G116-10 (CANL) - G118-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)


C323669E03
2.552,0.469 3,0.698 0.448,0.229 4.24,0.448 4.677,0.698 0.438,0.25 4.521,2.406 4.365,2.406 4.365,2.406 4.021,1.594 true 3.219,2.417 3.385,2.417 3.385,2.417 3.708,1.49 true 1.24,2.427 1.385,2.427 1.385,2.427 1.771,1.5 true 1.219,0.479 1.385,0.479 1.385,0.479 1.781,1.292 true 2.635,0.5 3.094,0.698 0.458,0.198 10 false C39 4.333,0.49 4.604,0.656 0.271,0.167 10 true C40 0.771,0.396 1.229,0.656 0.458,0.26 10 false CANH 0.823,2.365 1.25,2.646 0.427,0.281 10 false CANL 2.958,2.344 3.573,2.542 0.615,0.198 10 false +B 4.604,2.323 5.219,2.521 0.615,0.198 10 false GND

a.
C325480C06
1.521,0.365 1.927,0.615 0.406,0.25 1.427,2.292 1.792,2.542 0.365,0.25 0.521,1.458 0.969,1.927 0.969,1.927 1.135,1.927 true 2.302,3.573 2.708,4.25 2.708,4.25 2.854,4.25 true 2.719,0.573 2.844,0.573 2.844,0.573 2.906,1.229 true 2.688,1.958 2.813,1.958 2.813,1.958 2.906,1.448 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.406 2.063,0.604 0.458,0.198 10 false C39 1.49,2.333 1.948,2.531 0.458,0.198 10 false C40 1.188,1.896 1.5,2.094 0.313,0.198 10 false +B 2.906,4.177 3.219,4.375 0.313,0.198 10 false GND 2.271,1.885 2.729,2.083 0.458,0.198 10 false CANL 2.271,0.5 2.729,0.698 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C39-20 (CANH) - C39-40 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C39-20 (CANH) - C40-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C39-40 (CANL) - C40-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
C39-20 (CANH) - C39-21 (+B) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C39-40 (CANL) - C39-21 (+B) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


C278749E03
3.375,0.25 3.854,0.542 0.479,0.292 2.417,0.25 2.75,0.25 2.75,0.25 3.375,1.417 true 2.167,0.5 2.5,0.5 2.5,0.5 3.25,1.406 true 4.365,1.521 5.063,2.417 5.063,2.417 5.417,2.417 true 2.083,2.417 2.417,2.417 2.417,2.417 3.083,1.406 true 3.479,0.333 3.938,0.531 0.458,0.198 10 false G33 1.917,0.427 2.167,0.615 0.25,0.188 10 false TX- 1.75,2.333 2.208,2.531 0.458,0.198 10 false GND 2.125,0.177 2.417,0.375 0.292,0.198 10 false TX+ 5.479,2.333 5.938,2.531 0.458,0.198 10 false B

a.
C240157C59
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.344,1.063 0.802,1.26 0.458,0.198 10 false G33 2.333,0.406 2.792,0.604 0.458,0.198 10 false TX+ 2.24,0.156 2.698,0.354 0.458,0.198 10 false TX- 3.031,1.531 3.333,1.802 0.302,0.271 10 false B 0.667,0.385 1.031,0.646 0.365,0.26 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G33-11 (TX+) - G33-12 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G33-11 (TX+) - G33-14 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G33-12 (TX-) - G33-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G33-11 (TX+) - G33-21 (B) GR - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G33-12 (TX-) - G33-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)


E101528E47
3.313,0.156 3.792,0.365 0.479,0.208 1.677,1.469 1.844,1.469 1.844,1.469 2.333,0.865 true 1.719,0.354 1.885,0.354 1.885,0.354 2.677,0.76 true 2.146,0.156 2.313,0.156 2.313,0.156 2.875,0.76 true 3.417,0.167 3.771,0.396 0.354,0.229 10 false G80 1.729,0.063 2.344,0.26 0.615,0.198 10 false CANH 1.313,0.25 1.927,0.448 0.615,0.198 10 false CANL 1.438,1.375 2.052,1.573 0.615,0.198 10 false E1

a.
C281183C08
1.573,0.229 1.938,0.49 0.365,0.26 0.292,2.51 0.656,2.771 0.365,0.26 2.552,3.094 2.406,3.094 2.406,3.094 2.219,2.823 true 2.958,0.552 2.813,0.552 2.813,0.552 2.375,0.979 true 2.688,0.281 2.542,0.281 2.542,0.281 2.24,0.979 true 2,1.885 2.188,1.885 2.188,1.885 2.625,1.052 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.104,1.979 0.417,2.135 0.313,0.156 10 false *b 0.385,2.542 0.698,2.698 0.313,0.156 10 false G7 2.625,3.01 3.083,3.26 0.458,0.25 10 false BAT 1.635,0.271 1.948,0.427 0.313,0.156 10 false G80 2.729,0.177 3.219,0.375 0.49,0.198 10 false CANH 3.01,0.448 3.427,0.677 0.417,0.229 10 false CANL 1.75,1.76 1.979,1.958 0.229,0.198 10 false E1
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G80-6 (CANH) - G80-7 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-6 (CANH) - G80-9 (E1) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-7 (CANL) - G80-9 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-6 (CANH) - G7-16 (BAT) V - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-7 (CANL) - G7-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher