Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2015.11
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197662 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the body ECU which causes the intrusion sensor to stop operating.

WIRING DIAGRAM

B433600E02
1.813,1.031 4.469,1.333 2.656,0.302 10 false Intrusion Sensor Cancel Switch 1.781,0.74 2.24,0.938 0.458,0.198 10 false GND 3.469,0.75 3.927,0.948 0.458,0.198 10 false IND2 5.271,0.844 5.729,1.042 0.458,0.198 10 false SSW1 5.323,1.583 6.708,2 1.385,0.417 10 false Body ECU 5.313,1.417 5.771,1.615 0.458,0.198 10 false G27 2.188,1.417 2.646,1.615 0.458,0.198 10 false Q3 2.188,1.583 3.854,1.979 1.667,0.396 10 false Map Light Assembly 1.615,0.76 2.073,0.958 0.458,0.198 10 false 3 3.854,0.75 4.313,0.948 0.458,0.198 10 false 7 5.01,0.76 5.469,0.958 0.458,0.198 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BODY ECU - MAP LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G27 body ECU connector.


b.

Disconnect the Q3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G27-10 (SSW1) - Q3-7 (IND2) Always Below 1 Ω
Q3-3 (GND) - Body ground Always Below 1 Ω
G27-10 (SSW1) - Body ground Always 10 kΩ or higher
Q3-7 (IND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LAMP ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LAMP ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
E320541E02
2,1.01 2.427,0.427 true 1.281,1.01 0.813,0.417 true 0.583,0.25 1.344,0.479 0.76,0.229 10 false IND2 2.344,0.229 2.802,0.427 0.458,0.198 10 false GND

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (IND2) - 3 (GND) Intrusion sensor cancel switch not pressed 10 kΩ or higher
7 (IND2) - 3 (GND) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)