Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › from 2015.11
RM33J0E _57 Power Source / Network _038493 NETWORKING _0190453 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
AFS ECU Communication Stop Mode Either condition is met:
·

"Headlight swivel (AFS)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of headlight leveling ECU assembly

·

Headlight leveling ECU assembly ground circuit

·

Headlight leveling ECU assembly CAN branch wire or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

C279376E35
5,4.104 5.719,4.469 0.719,0.365 10 false G80 5.01,4.271 7.104,4.615 2.094,0.344 10 false Headlight Leveling ECU Assembly 5.646,3.479 7.073,3.792 1.427,0.313 10 false E1 5.667,2.635 7.094,2.948 1.427,0.313 10 false IG 5.667,1.75 7.094,2.063 1.427,0.313 10 false CANL 5.656,1.177 7.083,1.49 1.427,0.313 10 false CANH 5.417,1.635 6.844,1.948 1.427,0.313 10 false 7 5.406,1.042 6.833,1.354 1.427,0.313 10 false 6 5.427,2.531 6.854,2.844 1.427,0.313 10 false 1 5.438,3.344 6.865,3.656 1.427,0.313 10 false 9 4.052,2.458 5.479,2.771 1.427,0.313 10 false IG1 NO.4 0.552,2.594 3.333,2.979 2.781,0.385 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 1.729,1.594 2.042,1.969 0.313,0.375 10 false 18 1.719,1.01 2.24,1.333 0.521,0.323 10 false 8 0.292,2.042 1,2.385 0.708,0.344 10 false G67 0.302,2.208 2.552,2.49 2.25,0.281 10 false No. 1 CAN Junction Connector 0.292,3.979 2.875,4.292 2.583,0.313 10 false *1: w/ Smart Entry and Start System 0.281,4.344 2.927,4.667 2.646,0.323 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY CAN BRANCH WIRE)
a.
C317100C08
1.458,0.24 1.906,0.542 0.448,0.302 2.375,1.052 2.51,0.469 2.51,0.469 2.635,0.469 true 1.927,1.844 2.073,1.844 2.073,1.844 2.25,1.135 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.563,0.313 2.042,0.615 0.479,0.302 10 false G80 1.469,1.76 1.938,1.969 0.469,0.208 10 false CANH 2.708,0.385 3.323,0.583 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-6 (CANH) - G80-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HEADLIGHT LEVELING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C317100C09
1.531,0.281 1.979,0.563 0.448,0.281 0.385,0.479 0.542,0.479 0.542,0.479 0.792,1.042 true 2.646,1.042 2.781,0.458 2.781,0.458 2.927,0.458 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.625,0.333 2.167,0.719 0.542,0.385 10 false G80 0.208,0.375 0.417,0.656 0.208,0.281 10 false IG 2.99,0.375 3.302,0.573 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-9 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR