Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TASA Made) › from 2015.11
RM33J0E _52 Drivetrain _038471 DRIVE SHAFT / PROPELLER SHAFT _0233203 PROPELLER SHAFT ASSEMBLY(for TASA Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TASA Made)  REMOVAL  


PROCEDURE

Hide 51569 1.REMOVE PROPELLER SHAFT GUARD

a.

for Pre-Runner:

i.
C330861

for Transmission side:

Remove the 2 bolts and propeller shaft guard.


ii.
C330862

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



b.

for 4WD:

i.
C330864

for Transfer side:

Remove the 2 bolts and propeller shaft guard.


ii.
C330863

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



Hide 37100 2.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

a.
C330860C01
1.698,1.292 2.521,1.844 2.521,1.844 1.698,1.448 true 2.594,1.771 2.906,1.969 0.313,0.198 10 true *a
*a Matchmark


w/o Differential Torsional Damper:

Place matchmarks on the propeller shaft flange and differential flange.


b.
C317880C01
1.656,4.021 2.531,4.177 2.531,4.177 1.667,3.938 true 1.75,1.479 2.438,1.906 2.438,1.906 1.75,1.594 true 2.583,4.104 2.896,4.302 0.313,0.198 10 true *a 2.521,1.844 2.833,2.042 0.313,0.198 10 true *a
*a Matchmark


w/ Differential Torsional Damper:

Place matchmarks on the propeller shaft flange, differential torsional damper and differential flange.


c.

Remove the 4 nuts and 4 washers and disconnect the propeller shaft with center bearing assembly.


d.
C330865

Remove the 2 set bolts of the center support bearing from the frame crossmember.


e.

Pull out the propeller shaft with center bearing assembly.

NOTICE:

When pulling out the propeller shaft with center bearing assembly, make sure that transmission fluid does not leak from the extension housing.


HINT:

Transmission fluid may leak from the extension housing there fore, use a container to catch the fluid.



f.
C317881

w/ Differential Torsional Damper:

Remove the differential torsional damper.


Hide 37100 3.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

a.
C330859C01
1.625,1.438 2.49,1.677 2.49,1.677 1.615,1.271 true 2.521,1.594 2.833,1.792 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and transfer flange.


b.

Remove the 4 nuts and 4 washers and disconnect the propeller shaft with center bearing assembly.


c.
C330860C02
1.708,1.448 2.5,1.802 2.5,1.802 1.688,1.271 true 2.563,1.729 2.875,1.927 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and differential flange.


d.

Remove the 4 nuts and 4 washers.


e.
C118612

Remove the 2 set bolts of the center support bearing from the frame crossmember.


f.

Remove the propeller shaft with center bearing assembly.