Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TASA Made) › 2015.11–2016.07
RM33J0E _52 Drivetrain _038471 DRIVE SHAFT / PROPELLER SHAFT _0233203 PROPELLER SHAFT ASSEMBLY(for TASA Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TASA Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:

The following chart describes vehicle types A and B, which are referred to throughout the procedure.

for Pre-Runner:
Vehicle Type A Vehicle Type B
Engine Type Transmission Type Engine Type Transmission Type
2TR-FE R151 1GD-FTV RC61
- - 1KD-FTV RC61
- - 2GD-FTV RC60
- - 2KD-FTV RC61

for 4WD:
Vehicle Type A Vehicle Type B
Engine Type Transmission Type Engine Type Transmission Type
1KD-FTV A750F 1GD-FTV AC60F
2TR-FE R151F RC61F
- - 1KD-FTV RC61F
- - 2GD-FTV RC60F
- - 2KD-FTV RC61F


PROCEDURE

Hide 37230 1.INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY

a.
C346139C02
1.219,3.531 0.771,3.052 0.771,3.052 1.219,2.615 true 2.135,3.5 2.479,3.063 2.479,3.063 2.135,2.635 true 2.917,1.125 3.167,1.125 true 1.375,0.156 1.688,0.354 0.313,0.198 10 false *a 0.573,2.958 0.885,3.156 0.313,0.198 10 false *b 2.594,2.979 2.906,3.177 0.313,0.198 10 false *b 3.198,1.042 3.406,1.24 0.208,0.198 10 false *c
*a Front Side
*b Seal
*c Engraved Arrow


Install the center No. 1 support bearing assembly to the intermediate shaft.

NOTICE:
·

Carefully insert the part so that the seal does not invert.

·

Make sure to install the part so that the engraved arrow faces the front of the vehicle.




b.

Install the 2 washers to the intermediate shaft.


c.
C118617C08
1.74,1.115 1.74,0.521 1.74,0.521 2.698,0.521 true 1.76,1.25 2.115,1.25 2.115,1.25 2.115,0.521 true 2.74,0.458 3,0.635 0.26,0.177 10 false *a
*a Matchmark


Align the matchmarks on the center yoke and intermediate shaft, and then install the center yoke to the intermediate shaft.


d.

Install the washer to the intermediate shaft.


e.
C118620

Clamp the center yoke in a vise between aluminum plates and press the bearing into position by installing a new lock nut.

Torque:
127.5 N*m (1300 kgf*cm, 94 ft.*lbf)


f.
C118621

Using a chisel and hammer, stake the lock nut.

NOTICE:
·

Fully stake the lock nut along the entire groove.

·

Do not damage the threads of the intermediate shaft.




Hide 2.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for all universal joint spider assemblies.


a.
C060598

Apply grease to a new universal joint spider assembly and 2 new spider bearings.

Grease:

Lithium base chassis grease NLGI No. 2


NOTICE:

Do not apply too much grease.



b.

Install the universal joint spider assembly to the flange yoke.


c.
C281350N01
1.021,0.833 1.125,0.354 1.125,0.354 1.292,0.354 false 1.344,0.271 1.688,0.458 0.344,0.188 10 false SST

Using SST, install the spider bearing to the universal joint spider assembly.

SST
09332-25010  


d.

Using SST, adjust both spider bearings so that the snap ring grooves are as wide as possible and equal in width.

SST
09332-25010  


e.
F052434

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

NOTICE:

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.


Standard Snap Ring Thickness:
for Vehicle Type A
Part No. Color Thickness

*: For cup with grease nipple.

90080-52038 Blue 1.638 mm (0.0645 in.)
90080-52039 Yellow 1.588 mm (0.0625 in.)
90080-52040 White 1.537 mm (0.0605 in.)
90080-52041 Black 1.486 mm (0.0585 in.)
90080-52042 Copper 1.511 mm (0.0595 in.)
90080-52156* - -

for Vehicle Type B
Part No. Mark Thickness

*: For cup with grease nipple.

90521-A0003* Black 1.486 mm (0.0587 in.)
90521-A0005* Yellow 1.588 mm (0.0626 in.)
90521-A0006* Copper 1.512 mm (0.0594 in.)
90521-A0008 Black 1.517 mm (0.0598 in.)
90521-A0010 Blue 1.638 mm (0.0646 in.)
90521-A0011 Black 1.542 mm (0.0606 in.)
90521-A0013 Black 1.618 mm (0.0638 in.)
90521-A0014 Black 1.486 mm (0.0587 in.)
90521-A0015 Copper 1.512 mm (0.0594 in.)
90521-A0016 White 1.556 mm (0.0614 in.)


NOTICE:
·

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196in.), select 2 snap rings that have as close to the same thickness as possible.

·

Use a new snap ring.

·

Use a snap ring with as close to the same thickness as possible on both ends.




f.
C282524C01
2.365,0.656 1.656,0.302 1.656,0.302 1.333,0.302 true 1.115,0.198 1.427,0.354 0.313,0.156 10 false *a
*a Hammering Point


Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



g.

Align the matchmarks on the flange yoke and propeller shaft.


h.

for Pre-Runner:

i.
C330807C01
1.688,0.792 2.833,1.49 2.833,1.49 1.854,0.635 true 2.938,1.448 3.25,1.646 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the center yoke and propeller shaft.


ii.
C330806C01
1.448,1.49 2.542,1.885 2.542,1.885 1.531,1.25 true 2.625,1.823 2.938,2.021 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the sleeve yoke and intermediate shaft.



i.

for 4WD:

i.
C330805C01
1.625,0.844 2.698,1.25 2.698,1.25 1.771,0.656 true 2.75,1.177 3.063,1.375 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the center yoke and sleeve yoke.


ii.
C330804C01
1.708,1.51 2.531,1.708 2.531,1.708 1.896,1.354 true 2.615,1.625 2.927,1.823 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the flange yoke and intermediate shaft.



j.
C307744C01
1.167,1 1.167,0.417 1.167,0.417 1.25,0.417 true 2.5,1.333 2.865,1.323 true 1.323,1.573 1.635,1.771 0.313,0.198 10 false *a 0.979,0.125 1.292,0.323 0.313,0.198 10 false *b 1.292,0.333 1.75,0.531 0.458,0.198 10 false SST 2.948,1.25 3.167,1.469 0.219,0.219 10 false A
*a Turn
*b Hold


Using SST, install the 2 spider bearings to the universal joint spider assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



k.

Using SST, adjust both spider bearings so that the front propeller shaft joint spider bearing snap ring grooves are as wide as possible and equal in width.

SST
09332-25010  


l.
F052434

Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.

NOTICE:

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.


HINT:

Do not reuse the snap rings.


NOTICE:
·

While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196in.), select 2 snap rings that have as close to the same thickness as possible.

·

Use a new snap ring.

·

Use a snap ring with as close to the same thickness as possible on both ends.



Standard Snap Ring Thickness:
for Vehicle Type A
Part No. Color Thickness

*: For cup with grease nipple.

90080-52038 Blue 1.638 mm (0.0645 in.)
90080-52039 Yellow 1.588 mm (0.0625 in.)
90080-52040 White 1.537 mm (0.0605 in.)
90080-52041 Black 1.486 mm (0.0585 in.)
90080-52042 Copper 1.511 mm (0.0595 in.)
90080-52156* - -

for Vehicle Type B
Part No. Mark Thickness

*: For cup with grease nipple.

90521-A0003* Black 1.486 mm (0.0587 in.)
90521-A0005* Yellow 1.588 mm (0.0626 in.)
90521-A0006* Copper 1.512 mm (0.0594 in.)
90521-A0008 Black 1.517 mm (0.0598 in.)
90521-A0010 Blue 1.638 mm (0.0646 in.)
90521-A0011 Black 1.542 mm (0.0606 in.)
90521-A0013 Black 1.618 mm (0.0638 in.)
90521-A0014 Black 1.486 mm (0.0587 in.)
90521-A0015 Copper 1.512 mm (0.0594 in.)
90521-A0016 White 1.556 mm (0.0614 in.)



m.
C258229C01
1.646,2.031 1.896,2.031 1.896,2.031 2.344,1.792 false 1.458,1.938 1.667,2.125 0.208,0.188 10 *a
*a Hammering Point


Using a hammer, tap the propeller shaft until there is no clearance between the spider bearing outer race and snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



Hide 37334C 3.INSTALL REAR SLIDING SHAFT BOOT (for 4WD)

a.
C330886C02
1.385,2.229 1.385,2.979 1.385,2.979 1.229,2.979 true 1.333,2 1.333,0.167 1.333,0.167 1.5,0.167 true 1.5,1.75 1.5,0.667 1.5,0.667 1.667,0.667 true 1.99,1.74 1.99,1.156 1.99,1.156 2.156,1.156 true 2.583,1.781 2.583,0.677 2.583,0.677 2.75,0.677 true 2.698,2 2.698,1.146 2.698,1.146 2.865,1.146 true 2.74,2.229 2.74,2.563 2.74,2.563 2.906,2.563 true 2.167,2.75 2.583,2.75 true 1.771,0.573 2.083,0.729 0.313,0.156 10 false *1 2.219,1.083 2.531,1.24 0.313,0.156 10 false *2 1.031,2.896 1.344,3.052 0.313,0.156 10 false *b 2.646,2.667 2.958,2.823 0.313,0.156 10 false *c 2.813,0.604 3.125,0.76 0.313,0.156 10 false *1 1.563,0.083 1.875,0.24 0.313,0.156 10 false *a 2.958,1.052 3.271,1.208 0.313,0.156 10 false *a 2.969,2.479 3.281,2.635 0.313,0.156 10 false *b
*1 Propeller Shaft Boot Clamp
*2 Rear Sliding Shaft Boot
*a Matchmark of Propeller Shaft and Sleeve Yoke
*b Matchmark of Pinching Portion of Propeller Shaft Boot Clamp
*c Pinching Portion


Temporarily install a new rear sliding shaft boot to the propeller shaft with 2 new clamps.


b.

Coat the splines of the propeller shaft with MP grease.

Standard Grease Capacity:

7.0 to 10.0 g (0.25 to 0.35 oz)



c.

Align the matchmarks on the propeller shaft and sleeve yoke.


d.

Install the sleeve yoke to the propeller shaft and connect the rear sliding shaft boot.


e.

Align the matchmarks on the propeller shaft, sleeve yoke and the pinching portions of the 2 rear propeller shaft boot clamps.

HINT:

Make sure to align the matchmarks of the propeller shaft boot clamp.

If the pinching portions are installed at different locations than where they were located before disassembly, the rotational balance of the propeller shaft cannot be ensured, which may result in vibrations and noise.



f.
C346180C01
2.771,1.771 2.594,1.771 2.594,1.771 2,1 true 2.958,0.854 3.271,1.052 0.313,0.198 10 false *a 1.677,0.542 1.99,0.74 0.313,0.198 10 false *b 2.823,1.677 3.271,1.927 0.448,0.25 10 false SST
*a Turn
*b Hold


Secure one of the rear propeller shaft boot clamps to the rear sliding shaft boot.

HINT:
·

Use the same procedure for each rear propeller shaft boot clamp.

·

Make sure that the matchmarks of the pinching portion of the rear propeller shaft boot clamp are aligned.



i.

Install SST to the rear propeller shaft boot clamp, and then while pressing the rear sliding shaft boot, slightly tighten the SST bolt.

SST
09521-24010  

NOTICE:
·

Correctly set the rear propeller shaft boot clamp to the guide groove.

·

Do not damage the rear sliding shaft boot.




ii.

Tighten SST so that the boot clamp is pinched as shown in the illustration.

Standard clearance:

3.1 mm (0.122 in.) or less


NOTICE:
·

When tightening SST, make sure the clearance of the rear propeller shaft boot clamp is within the standard clearance.

·

Do not damage the rear sliding shaft boot.




iii.

Remove SST from the rear propeller shaft boot clamp.


iv.
C118611N01
1.906,1.052 2.938,1.531 true 3,1.51 3.323,1.677 0.323,0.167 10 false SST

Using SST, measure the clearance of the rear propeller shaft boot clamp.

SST
09240-00020  

Standard clearance:

3.1 mm (0.122 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the rear propeller shaft boot clamp.




Hide 4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with grease.

Grease:

Lithium base chassis grease NLGI No. 2




C354026C01
3.667,5 3.667,4.583 3.667,4.583 3.833,4.583 false 1.281,5 1.281,4.833 1.281,4.833 1.781,4.833 false 6.271,5 6.271,4.583 6.271,4.583 6.438,4.583 false 4.688,2.125 4.688,1.708 4.688,1.708 4.854,1.708 false 6.208,2.104 6.208,1.688 6.208,1.688 6.375,1.688 false 2.396,2.125 2.396,1.958 2.396,1.958 2.896,1.958 false 0.156,0.094 0.469,0.25 0.313,0.156 10 false *A 0.323,2.885 0.635,3.042 0.313,0.156 10 false *B 3.01,1.885 3.323,2.042 0.313,0.156 10 false *1 4.969,1.646 5.281,1.802 0.313,0.156 10 false *2 6.448,1.615 6.76,1.771 0.313,0.156 10 false *3 1.865,4.771 2.177,4.927 0.313,0.156 10 false *1 3.917,4.51 4.229,4.667 0.313,0.156 10 false *2 6.51,4.5 6.823,4.656 0.313,0.156 10 false *3 2.927,0.833 3.24,0.99 0.313,0.156 10 false *a 2.896,3.927 3.208,4.083 0.313,0.156 10 false *a 1.063,0.615 1.531,0.781 0.469,0.167 10 false *1*2*3 1.052,3.469 1.521,3.635 0.469,0.167 10 false *1*2*3
*A for Pre-Runner (Vehicle Type B) *B for 4WD
*1 No. 1 Grease Fitting *2 No. 2 Grease Fitting
*3 No. 3 Grease Fitting - -
*a Vehicle Rear - -