Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1GD-FTV, 2GD-FTV) › from 2015.11
RM33J0E _58 Vehicle Interior _038504 HEATING / AIR CONDITIONING _0192220 COMPRESSOR(for 1GD-FTV, 2GD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GD-FTV, 2GD-FTV)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.

Clamp the compressor assembly with magnet clutch in a vise between aluminum plates.


b.
E316317

Install the magnet clutch stator with the parts aligned as shown in the illustration.


c.
E316319C01
0.75,0.604 1.063,0.76 0.313,0.156 10 false *a 0.25,0.646 0.563,0.802 0.313,0.156 10 false *b 1.229,0.625 1.542,0.781 0.313,0.156 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install a new snap ring with the chamfered side facing outward.

NOTICE:

When installing the snap ring, do not widen it excessively.



d.
E316321C01
0.74,0.594 1.052,0.75 0.313,0.156 10 false *a 0.26,0.667 0.573,0.823 0.313,0.156 10 false *b 1.156,0.656 1.469,0.813 0.313,0.156 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.




e.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.



f.
E344430C01
0.625,0.479 0.76,0.479 0.76,0.479 0.979,0.771 false 0.698,3.021 0.833,3.021 0.833,3.021 1.01,3.188 true 0.031,0.073 0.344,0.229 0.313,0.156 10 false *A 0.083,2.583 0.396,2.74 0.313,0.156 10 false *B 0.438,0.385 0.75,0.542 0.313,0.156 10 false *a 0.51,2.906 0.823,3.063 0.313,0.156 10 false *a
*A for Type A
*B for Type B
*a SST


for Type A:

Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00270  

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub.



g.

for Type B:

Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00040  

Torque:
13.2 N*m (135 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub.



Hide 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
E344432C01
0.031,0.031 0.344,0.188 0.313,0.156 10 false *A 0.063,2.448 0.375,2.604 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Set a dial indicator to the magnet clutch hub.


b.

Connect a battery positive lead to terminal 1 of the magnet clutch connector and a negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard Clearance:
for Type A:

0.30 to 0.55 mm (0.0118 to 0.0217 in.)

for Type B:

0.25 to 0.50 mm (0.0098 to 0.0197 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet Clutch Washer Thickness:

0.1 mm (0.00394 in.)

0.3 mm (0.0118 in.)

0.5 mm (0.0197 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



c.

Remove the compressor assembly with magnet clutch from the vise.


Hide 88688N 3.INSTALL COOLER BRACKET

a.
E344428C01
0.042,0.031 0.354,0.188 0.313,0.156 10 true *A 0.063,2.49 0.375,2.646 0.313,0.156 10 true *B
*A for Type A
*B for Type B


Install the cooler bracket with the screw.


b.

Attach the clamp.