AIR CONDITIONING AMPLIFIER ASSEMBLY
Disconnect the G33 air conditioning amplifier assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-1 (IG+) - Body ground | G - Body ground | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| G33-14 (GND) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 Ω |
| G33-21 (B) - Body ground | W - Body ground | Power source (Back-up) | Always | 11 to 14 V |
Reconnect the G33 air conditioning amplifier assembly connector.
Measure the resistance, voltage and check for waveform according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-9 (PSW) - Body ground | L - Body ground | Air conditioner pressure switch signal | ·
Engine running ·
Refrigerant pressure normal ·
Blower switch: On (LO level) ·
"A/C" switch: On |
Below 1 V |
·
Engine running ·
Refrigerant pressure less than 0.196 MPa (2.0 kgf/cm2, 28 psi) or more than 3.14 MPa (32.0 kgf/cm2, 455 psi) ·
Blower switch: On (LO level) ·
"A/C" switch: On |
11 to 14 V | |||
| G33-11 (TX+) | GR | CAN communication line | - | - |
| G33-12 (TX-) | W | CAN communication line | - | - |
| G33-17 (AC1) - Body ground | GR - Body ground | Idle-up request signal | ·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: Off |
11 to 14 V |
·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: On |
Below 1 V | |||
| G33-20 (MGC) - Body ground | V - Body ground | Magnet clutch drive output signal | ·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: Off or on (magnet clutch off) |
11 to 14 V |
·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: On (magnet clutch on) |
Below 1 V | |||
| G33-22 (BLW) - Body ground | P - Body ground | Blower motor speed control signal | ·
Engine switch on (IG) ·
Blower switch: On (LO level) |
Pulse generation
(See Waveform 1) |
| G33-24 (ACT) - Body ground | LG - Body ground | Magnet clutch on permit input signal | ·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: Off or on (magnet clutch off) |
Below 1 V |
·
Engine running ·
Blower switch: On (LO level) ·
"A/C" switch: On (magnet clutch on) |
4.5 to 5.5 V | |||
| G33-29 (TR) - G33-34 (SG-2) | V - L | Room temperature sensor signal | ·
Engine switch on (IG) ·
Cabin temperature: 25°C (77°F) |
1.8 to 2.2 V |
·
Engine switch on (IG) ·
Cabin temperature: 40°C (104°F) |
1.2 to 1.6 V | |||
| G33-30 (S5-3) - Body ground | G - Body ground | Power supply for solar sensor | Engine switch on (IG) | 4.5 to 5.5 V |
| G33-33 (TSD) - Body ground | P - Body ground | Solar sensor signal | ·
Engine switch on (IG) ·
Solar sensor subjected to electric light |
0.8 to 4.3 V |
·
Engine switch on (IG) ·
Solar sensor covered with cloth |
Below 0.8 V | |||
| G33-34 (SG-2) - Body ground | L - Body ground | Ground for room temperature sensor | Always | Below 1 Ω |
| G33-37 (LIN1) - Body ground | R - Body ground | LIN communication signal | Engine switch on (IG) | Pulse generation |
| za-3 (BUS) - za-2 (BUSG) | - | BUS IC control signal | Engine switch on (IG) | Pulse generation
(See Waveform 2) |
| za-2 (BUSG) - Body ground | - | Ground for BUS IC | Always | Below 1 Ω |
| za-4 (BBUS) - za-2 (BUSG) | - | Power supply for BUS IC | Always | 11 to 14 V |
| za-5 (SG-4) - Body ground | GR - Body ground | Ground for evaporator temperature sensor | Always | Below 1 Ω |
| za-6 (TE) - za-5 (SG-4) | GR - GR | Evaporator temperature sensor signal | ·
Engine switch on (IG) ·
Evaporator temperature: 0°C (32°F) |
1.7 to 2.1 V |
·
Engine switch on (IG) ·
Evaporator temperature: 15°C (59°F) |
0.9 to 1.3 V |
Waveform 1:
| Item | Content |
|---|---|
| Terminal No. | G33-22 (BLW) - Body ground |
| Tool Setting | 2 V/DIV., 500 μs/DIV. |
| Vehicle Condition | ·
Engine switch on (IG) ·
Blower switch: On (LO level) |
Waveform 2:
| Item | Content |
|---|---|
| Terminal No. | za-3 (BUS) - za-2 (BUSG) |
| Tool Setting | 2 V/DIV., 2 ms/DIV. |
| Vehicle Condition | Engine switch on (IG) |
AIR CONDITIONING CONTROL ASSEMBLY
Disconnect the G32 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G32-2 (IG) - Body ground | L - Body ground | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| G32-4 (GND) - Body ground | W-B - Body ground | Ground for air conditioning control assembly | Always | Below 1 Ω |
Reconnect the G32 air conditioning control assembly connector.
Measure the waveform according to the value(s) in the table below.
| Terminal No.
(Symbol) |
Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G32-3 (LIN1) - Body ground | R - Body ground | LIN communication signal | Engine switch on (IG) | Pulse generation |
ECM
for 1GD-FTV (w/ DPF):Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>TERMINALS OF ECM
for 1GD-FTV (for i-ART):Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>TERMINALS OF ECM