Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › DRIVE BELT › from 2016.07
RM33J0E _51 Engine / Hybrid System _053774 2TR-FBE ENGINE MECHANICAL _0261403 DRIVE BELT A

2TR-FBE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16603B 1.INSTALL TENSIONER PULLEY

NOTICE:

Perform the following procedure when it is necessary to replace the tensioner pulley.


HINT:

The tensioner pulley service kit consists of a bolt, dust seal and tensioner pulley.


a.
A302382C02
0.49,1.031 0.49,1.344 false 1.688,1.49 1.917,1.49 false 2.375,0.292 2.177,0.188 2.177,0.188 2.031,0.188 false 0.427,1.385 0.74,1.542 0.313,0.156 10 false *1 1.823,0.083 2.135,0.24 0.313,0.156 10 false *2 1.969,1.385 2.281,1.542 0.313,0.156 10 false *3
*1 Bolt
*2 Tensioner Pulley
*3 Dust Seal
V100135

Front


Install the dust seal and bolt to the tensioner pulley as shown in the illustration.

NOTICE:
·

The dust seal must be oriented correctly when installed. If the dust seal is installed incorrectly, the bearing may be damaged.

·

Do not touch the seal surface of the bearing.



HINT:

Be sure to use the bolt from the service kit.



b.

Tighten the bolt by hand until the flange of the bolt contacts the dust seal and the tensioner pulley is fixed in place.

NOTICE:

Do not use any tools.



c.

Tighten the bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


d.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 16361A 2.INSTALL FAN AND GENERATOR V BELT

a.
A348629C01
0.396,2.875 0.875,2.875 true 0.875,3.708 1.083,3.708 1.083,3.708 1.333,3.385 true 1.625,3.823 1.625,4.115 true 1.583,2.917 1.729,2.385 1.729,2.385 1.917,2.385 true 1.938,3.219 2.479,3.167 2.479,3.167 2.656,3.167 true 2.396,2.771 2.688,2.615 2.688,2.615 2.823,2.615 true 2.417,3.667 2.823,3.667 true 2.01,3.583 2.208,4.156 2.208,4.156 2.375,4.156 true 0.208,2.771 0.396,2.969 0.188,0.198 10 false *1 1.948,2.292 2.125,2.49 0.177,0.198 10 false *2 2.854,2.521 3.042,2.708 0.188,0.188 10 false *3 2.698,3.073 2.885,3.271 0.188,0.198 10 false *4 0.698,3.604 0.875,3.802 0.177,0.198 10 false *5 1.563,4.146 1.76,4.333 0.198,0.188 10 false *6 2.406,4.063 2.583,4.25 0.177,0.188 10 false *7 2.854,3.573 3.042,3.76 0.188,0.188 10 false *8
*1 Generator Assembly
*2 Idler Pulley Sub-assembly
*3 Vane Pump Assembly
*4 Fan Pulley
*5 Tensioner Pulley
*6 Crankshaft Pulley
*7 No. 1 Idler Pulley Sub-assembly
*8 Cooler Compressor Assembly


Install the fan and generator V belt to all the pulleys except the V-ribbed belt tensioner pulley.


b.

Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward, and then install the fan and generator V belt to the tensioner pulley.

NOTICE:
·

The backside of the fan and generator V belt should face the tensioner pulley.

·

Check that the fan and generator V belt is properly installed to each pulley.




Hide 16361A 3.INSPECT FAN AND GENERATOR V BELT