Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE UNIT › from 2016.07
RM33J0E _51 Engine / Hybrid System _053774 2TR-FBE ENGINE MECHANICAL _0261409 ENGINE UNIT A

2TR-FBE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11381 1.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Clean and degrease the contact surfaces of the rear engine oil seal retainer and cylinder block sub-assembly.


b.
A346838C01
0.917,1.865 1.104,2.063 0.188,0.198 10 false *a
*a Seal Packing


Apply seal packing in a continuous bead as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




c.

Install the rear engine oil seal retainer with the 6 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15777E 3.INSTALL UNION

a.

Install the union to the cylinder block sub-assembly.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 15609 4.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Using a hexagon wrench, install the oil filter bracket union.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Install a new oil filter bracket gasket to the oil filter bracket sub-assembly.


c.

Install a new O-ring to the oil filter bracket union.

NOTICE:

Apply a light coat of engine oil to a new O-ring and oil filter bracket sub-assembly.



d.

Install 2 new gaskets and the 2 screw plugs to the oil filter bracket sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Install the oil filter bracket sub-assembly with the 2 bolts and nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 15601 6.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 16281 7.INSTALL NO. 4 WATER BY-PASS HOSE

a.

Install the No. 4 water by-pass hose to the oil cooler assembly and union, and slide the clips to secure the hoses.


Hide 16288 8.INSTALL NO. 4 WATER BY-PASS PIPE

a.

Install the No. 4 water by-pass pipe with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 5 water by-pass hose to the oil cooler assembly, and slide the clip to secure the hose.


Hide 13471A 9.INSTALL CRANKSHAFT PULLEY SET KEY

a.

Install the 2 crankshaft pulley set keys to the crankshaft.


Hide 13554 10.INSTALL NO. 4 CHAIN VIBRATION DAMPER

a.

Install the No. 4 chain vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13507 11.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
A101978

Install the No. 2 crankshaft timing sprocket as shown in the illustration.

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 and No. 2 balanceshafts are at the bottom side.


HINT:

Install the No. 2 crankshaft timing sprocket with the front mark facing forward.



b.
A101339C03
2.75,0.344 1.531,0.104 1.531,0.104 1.448,0.104 true 2.75,0.635 3.083,1.51 3.083,1.51 3.167,1.51 true 3.083,1.51 2.698,2.625 true 2.927,2.781 2.083,3.125 2.083,3.125 1.948,3.125 true 2.135,3.094 2.51,2.844 true 1.24,0 1.469,0.198 0.229,0.198 10 false *a 1.76,3.021 1.948,3.229 0.188,0.208 10 false *a 3.198,1.427 3.417,1.635 0.219,0.208 10 false *b
*a Mark Plate (Yellow)
*b Timing Mark


As shown in the illustration, install the No. 2 chain sub-assembly on the No. 2 crankshaft timing sprocket and No. 2 balanceshaft driven gear with the painted marks aligned with the timing marks on the sprocket and gear.


c.
A101340C05
0.365,0.813 0.469,1.406 0.469,1.406 0.563,1.406 true 0.635,0.688 1.073,0.125 1.073,0.125 1.156,0.125 true 0.594,1.292 0.792,1.49 0.198,0.198 10 false *a 1.208,0.021 1.427,0.219 0.219,0.198 10 false *b
*a Mark Plate
*b Timing Mark


Fit the other mark link of the No. 2 crankshaft timing sprocket behind the large timing mark of the balanceshaft drive gear sub-assembly.


d.

Insert the balanceshaft drive gear shaft through the balanceshaft drive gear sub-assembly so that it fits into the thrust plate hole.


e.
A302844C04
0.958,0.938 1.74,0.635 true 0.917,1.104 1.75,0.625 1.75,0.625 1.927,0.625 false 0.698,0.646 1.531,0.167 1.531,0.167 1.708,0.167 true 0.448,0.813 0.552,2.083 0.552,2.083 0.719,2.083 true 1.75,0.073 1.969,0.26 0.219,0.188 10 false *b 2,0.531 2.188,0.74 0.188,0.208 10 false *c 0.771,1.979 0.979,2.156 0.208,0.177 10 false *a
*a Mark Plate
*b Large Timing Mark
*c Small Timing Mark


Align the small timing mark of the balanceshaft drive gear sub-assembly with the timing mark of the No. 1 balanceshaft driven gear.


f.

Install the bolt to the balanceshaft drive gear sub-assembly and tighten it.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


g.
A101342C05
2.844,0.292 2.302,0.094 2.302,0.094 2.146,0.094 true 0.604,0.542 1.313,0.177 1.313,0.177 1.479,0.177 true 0.802,0.781 1.448,0.719 1.448,0.719 0.781,0.927 true 2.833,0.552 2.833,1.344 true 2.781,2.677 2.906,1.823 2.906,1.823 3.031,1.823 true 0.354,0.615 0.125,1.24 0.125,1.24 0.125,1.333 true 2.969,2.833 2.365,3.292 2.365,3.292 2.688,2.875 true 1.938,0.021 2.125,0.198 0.188,0.177 10 false *a 0.063,1.365 0.25,1.552 0.188,0.188 10 false *a 2.177,3.229 2.344,3.396 0.167,0.167 10 false *a 1.51,0.073 1.688,0.271 0.177,0.198 10 false *c 1.479,0.625 1.667,0.792 0.188,0.167 10 false *d 2.792,1.375 2.979,1.563 0.188,0.188 10 false *b 3.083,1.74 3.323,1.927 0.24,0.188 10 false *b
*a Mark Plate
*b Timing Mark
*c Large Timing Mark
*d Small Timing Mark


Check that each timing mark is aligned with the corresponding mark plate.

NOTICE:

Check that the No. 1 cylinder is at TDC and that the weights of the No. 1 balanceshaft and No. 2 balanceshaft are at the bottom side.



Hide 13550 12.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 2 chain tensioner assembly with the nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Assemble the No. 2 chain tensioner assembly with the pin installed, then remove the pin after assembly. When doing this, do not push the chain vibration damper against the No. 2 chain sub-assembly.



b.
A101320C11
1.219,1.052 0.948,1.99 0.948,1.99 0.802,1.99 true 0.594,1.375 0.406,0.646 0.406,0.646 0.281,0.646 true 2.698,0.656 2.417,0.292 2.417,0.292 2.292,0.292 false 0.083,0.542 0.26,0.74 0.177,0.198 10 false *a 2.104,0.177 2.302,0.375 0.198,0.198 10 false *c 0.604,1.875 0.802,2.073 0.198,0.198 10 false *b
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.


c.

Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.


Hide 13563 13.INSTALL NO. 3 CHAIN VIBRATION DAMPER

a.

Install the No. 3 chain vibration damper with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13562 14.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the No. 2 chain vibration damper with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 15678A 15.INSTALL OIL CONTROL VALVE FILTER

a.

Check that no foreign matter is on the mesh part of the oil control valve filter.

If foreign matter is present, clean the part thoroughly.


b.

Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11101 17.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13070A 18.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 19.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13750 21.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 22.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13521 26.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A101308

Install the crankshaft timing gear or sprocket as shown in the illustration.


Hide 13561 27.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the bolt and nut.

Torque:
for bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Remove the hexagon wrench from the No. 2 chain tensioner assembly and release the plunger.


Hide 13506 28.INSTALL CHAIN SUB-ASSEMBLY

a.
A337689C01
2.708,0.948 2.125,1.063 2.125,1.063 2.708,0.698 true 1.125,0.583 1.344,1.302 1.344,1.302 1.01,0.781 true 2.917,2.031 2.74,2.031 2.74,2.031 2.51,2.26 true 0.469,2.052 0.594,2.052 0.594,2.052 0.896,2.25 true 3.135,2.667 3.042,2.667 3.042,2.667 2.49,2.365 true 0.896,2.344 0.427,2.688 0.427,2.688 0.302,2.688 true 2.5,3.417 2.385,3.417 2.385,3.417 1.75,3.917 true 1.813,4.031 1.583,4.479 1.583,4.479 1.458,4.479 true 1.875,4.073 2.042,4.302 2.042,4.302 2.042,4.438 true 2.552,3.333 2.823,3.563 0.271,0.229 10 true *1 1.271,4.385 1.458,4.594 0.188,0.208 10 false *a 0.271,1.958 0.458,2.146 0.188,0.188 10 false *b 1.969,4.448 2.146,4.625 0.177,0.177 10 false *c 1.042,0.052 1.229,0.229 0.188,0.177 10 true *d 1.781,3.323 1.958,3.5 0.177,0.177 10 true *e 2.948,1.948 3.135,2.135 0.188,0.188 10 false *b 0.125,2.594 0.302,2.781 0.177,0.188 10 false *a 3.177,2.583 3.375,2.771 0.198,0.188 10 false *a 1.292,1.323 1.479,1.521 0.188,0.198 10 false *a 1.917,0.969 2.115,1.167 0.198,0.198 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Mark Plate (Pink)
*c Mark Plate (Yellow)
*d Approximately 13°
*e Approximately 30°


As shown in the illustration, install the chain sub-assembly to the camshaft timing exhaust gear assembly and camshaft timing gear assembly with the mark plates aligned with the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly.

HINT:
·

The camshaft mark plate is pink.

·

The crankshaft mark plate is yellow.




b.
A101359

Use a rope to tie the chain sub-assembly of the crankshaft timing gear or sprocket. Tie the rope near the crankshaft timing gear or sprocket.

NOTICE:

After the chain tensioner has been installed, the rope must be removed.


HINT:

The rope is tied so that the chain sub-assembly will not jump a tooth.



Hide 13559 29.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A101303C26
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.281,1.615 2.51,1.823 0.229,0.208 10 false *b 0.479,1.875 0.667,2.073 0.188,0.198 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the No. 1 chain tensioner assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the No. 1 chain tensioner assembly and release the plunger.


Hide 13566B 31.INSTALL TIMING CHAIN GUIDE

a.

Install a new O-ring to the No. 1 camshaft bearing cap.


b.

Install the timing chain guide with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 32.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A336450C01
0.427,2 0.594,2 0.594,2 0.885,2.323 true 2.896,2.031 2.76,2.031 2.76,2.031 2.49,2.365 true 2.885,3.75 2.75,3.75 2.75,3.75 1.771,3.917 true 1.833,4.031 2.063,4.302 2.063,4.302 2.063,4.417 true 2.698,0.938 2.052,1.083 2.052,1.083 2.708,0.698 true 1.125,0.573 1.333,1.281 1.333,1.281 1,0.781 true 2.927,3.646 3.125,3.875 0.198,0.229 10 false *1 1.281,1.302 1.479,1.51 0.198,0.208 10 true *a 1.052,0.042 1.24,0.24 0.188,0.198 10 true *b 1.76,3.313 1.958,3.5 0.198,0.188 10 true *c 1.865,0.99 2.063,1.198 0.198,0.208 10 true *a 2.938,1.917 3.135,2.125 0.198,0.208 10 true *a 0.229,1.885 0.427,2.094 0.198,0.208 10 true *a 1.979,4.427 2.177,4.635 0.198,0.208 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°


Check that the No. 1 cylinder is set to TDC/compression.

i.

Rotate the crankshaft two full rotations, and then check that all timing marks are in the position shown in the illustration.

If the timing marks do not match, set the chain sub-assembly again.



Hide 11204 33.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.

Install a new No. 2 camshaft bearing cap oil hole gasket and 3 new No. 3 camshaft bearing cap oil hole gaskets to the No. 1 camshaft bearing cap.


b.

Install the cylinder head cover connector sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16100 34.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11302 35.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16620D 36.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11421 38.INSTALL OIL PAN STUD BOLT

NOTICE:

If an oil pan stud bolt is deformed or its threads are damaged, replace it.


A346839C01
3.25,1.76 3.083,1.76 3.083,1.76 2.854,1.302 true 3.365,0.552 3.573,0.24 3.573,0.24 3.708,0.24 true 3,2.01 2.802,2.01 2.802,2.01 2.583,1.542 true 2.031,2.51 2.219,2.698 0.188,0.188 10 false *a 2.052,3.042 2.25,3.229 0.198,0.188 10 false *b 2.677,2.719 2.875,2.917 0.198,0.198 10 false *c 4.854,2.719 5.052,2.917 0.198,0.198 10 false *d 4.854,3.115 5.052,3.313 0.198,0.198 10 false *e 5.49,2.885 5.667,3.073 0.177,0.188 10 false *f 3.292,1.656 3.438,1.844 0.146,0.188 10 false A 3.052,1.927 3.198,2.115 0.146,0.188 10 false B 3.75,0.146 3.896,0.333 0.146,0.188 10 false B 1.521,3.427 1.667,3.615 0.146,0.188 10 false A 4.344,3.417 4.49,3.604 0.146,0.188 10 false B
*a 16 mm (0.630 in.) *b 9.0 mm (0.354 in.)
*c 27 mm (1.06 in.) *d 8.5 mm (0.335 in.)
*e 8.0 mm (0.315 in.) *f 18 mm (0.709 in.)


a.

Using E5 and E6 "TORX" socket wrenches, install the oil pan stud bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 12101 39.INSTALL OIL PAN SUB-ASSEMBLY

Hide 15104 40.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 41.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12144 42.INSTALL OIL PAN COVER SILENCER

Hide 13471 43.INSTALL CRANKSHAFT PULLEY

Hide 12233 46.INSTALL NO. 1 VENTILATION CONNECTOR

a.

Install the No. 1 ventilation connector to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11201 47.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101J 48.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 49.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11301K 50.INSTALL CRANKSHAFT POSITION SENSOR

Hide 11301M 51.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 52.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 12204 53.INSTALL PCV VALVE SUB-ASSEMBLY

Hide 12108 54.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap sub-assembly.


b.

Install the oil filler cap sub-assembly.


Hide 89422 55.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 83530 57.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY