Home › Power Source / Network › 2TR-FBE BATTERY / CHARGING › CHARGING SYSTEM › from 2016.07
RM33J0E _57 Power Source / Network _053790 2TR-FBE BATTERY / CHARGING _0266849 CHARGING SYSTEM Y

2TR-FBE BATTERY / CHARGING  CHARGING SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.



The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Running conditions, driving conditions, weather conditions
How did it happen? Problem symptoms

Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.


Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

Result:
Proceed to
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, inspect the LIN communication function to ensure there are no malfunctions in the communication system.


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
HINT:

Refer to DTC Check / Clear.

Click herePower Source / Network>2TR-FBE BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click herePower Source / Network>2TR-FBE BATTERY / CHARGING>CHARGING SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Malfunctioning parts are not confirmed. A
Malfunctioning parts are confirmed. B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

13.ADJUST AND/OR REPAIR
8.OVERALL ANALYSIS AND TROUBLESHOOTING*
HINT:

Refer to Data List / Active Test.

Click herePower Source / Network>2TR-FBE BATTERY / CHARGING>CHARGING SYSTEM>DATA LIST / ACTIVE TEST


Result:
Result Proceed to
Malfunctioning parts are not confirmed. A
Malfunctioning parts are confirmed. B



A

9.CHECK ECM CIRCUIT

B

13.ADJUST AND/OR REPAIR
9.CHECK ECM CIRCUIT
HINT:

Refer to Terminals of ECM.

Click herePower Source / Network>2TR-FBE BATTERY / CHARGING>CHARGING SYSTEM>TERMINALS OF ECM


Result:
Result
OK
NG



OK

10.CHECK FOR INTERMITTENT PROBLEMS

NG

13.ADJUST AND/OR REPAIR
10.CHECK FOR INTERMITTENT PROBLEMS
HINT:

Refer to Symptom Simulation.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Result:
Proceed to
NEXT



NEXT

11.CONDUCT PARTS INSPECTION
11.CONDUCT PARTS INSPECTION
Result:
Proceed to
NEXT



NEXT

12.IDENTIFY PROBLEM
12.IDENTIFY PROBLEM
Result:
Proceed to
NEXT



NEXT

13.ADJUST AND/OR REPAIR
13.ADJUST AND/OR REPAIR
Result:
Proceed to
NEXT



NEXT

14.CONDUCT CONFIRMATION TEST
14.CONDUCT CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END