Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2016.07
RM33J0E _58 Vehicle Interior _038501 SUPPLEMENTAL RESTRAINT SYSTEMS _0189276 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

·

If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

B401137



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 2.DISPOSE OF HORN BUTTON ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the horn button assembly, use an unneeded vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:
·

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool

·
B401441

If the procedure is performed using unspecified SST, the airbag may deploy in an unforeseen situation and cause a serious accident.



i.
C110372N03
0.958,1.542 0.885,0.979 0.885,0.979 0.688,0.979 false 0.417,0.906 0.875,1.104 0.458,0.198 10 false SST

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N10
1.167,0.938 1.094,0.385 1.094,0.385 0.896,0.385 false 0.615,0.313 1.073,0.51 0.458,0.198 10 SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the SST connector to the airbag before inspecting SST.

·

If the airbag deploys due to malfunction of SST, it may cause a serious accident.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Remove the lower steering column cover.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL


d.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




e.

Disconnect the airbag connector from the spiral cable with sensor sub-assembly.

i.
B404065C01
0.615,2.427 1.219,2.094 true 1.271,1.979 1.583,2.135 0.313,0.156 10 false *a
*a Slider
V113147

Slide Direction


Slide the slider to release the lock, and then disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

i.
B404066N01
1.24,1.458 2.188,1.458 true 1.75,1.688 1.75,1.458 true 2.25,1.354 2.708,1.552 0.458,0.198 10 false SST

Connect the SST connector to the airbag connector of the spiral with cable sensor sub-assembly.

SST
09082-00700  09082-00780  

CAUTION:
·
B394903

Do not deploy if the steering wheel assembly and horn button assembly are loose.

·

If deployed while the steering wheel assembly and horn button assembly are loose, the steering wheel assembly and horn button assembly may fly off and cause serious injuries.



NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
B340835C02
0.729,1.521 0.646,0.917 0.646,0.917 0.521,0.917 false 1.604,1.896 1.917,2.052 0.313,0.156 10 false *a 0.208,0.844 0.667,1.042 0.458,0.198 10 false SST
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iii.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Remove the horn button assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL

CAUTION:
·
B394905

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394906

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

·
B394908

Always wear safety glasses and gloves when handling a deployed horn button assembly.

·

If the horn button assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the horn button assembly in a plastic bag.




i.

Dispose of the horn button assembly.

i.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B396586

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394907

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

·
B394909

Always wear safety glasses and gloves when handling a deployed horn button assembly.

·

If the horn button assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394910

Never dispose of a horn button assembly with an undeployed airbag.

·

If an undeployed horn button assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 3.DISPOSE OF HORN BUTTON ASSEMBLY (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:
·

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool

·
B401441

If the procedure is performed using unspecified SST, the airbag may deploy in an unforeseen situation and cause a serious accident.



i.
C110372N02
0.958,1.542 0.885,0.979 0.885,0.979 0.688,0.979 false 0.396,0.896 0.854,1.094 0.458,0.198 10 false SST

Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N10
1.167,0.938 1.094,0.385 1.094,0.385 0.896,0.385 false 0.615,0.313 1.073,0.51 0.458,0.198 10 SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the SST connector to the airbag before inspecting SST.

·

If the airbag deploys due to malfunction of SST, it may cause a serious accident.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.



b.

Remove the horn button assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B104882C28
1.99,1.594 1.99,1.25 false 2.656,0.51 2.969,0.667 0.313,0.156 10 *a 1.917,1.625 2.229,1.781 0.313,0.156 10 *b
*a Wire Diameter
*b Stripped Wire


Using braided wire, tie down the horn button assembly to an unneeded tire.

Wire:
Cross-sectional area of stripped wire:

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the horn button assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.
B444336C03
2,2.146 2.427,1.521 2.427,1.521 2.438,2.094 false 2.427,1.521 2.719,1.521 false 2.104,4.25 2.531,3.625 2.531,3.625 2.542,4.198 false 2.542,3.625 2.833,3.625 false 0.042,0.063 0.354,0.219 0.313,0.156 12 false *A 0.042,2.125 0.354,2.281 0.313,0.156 12 false *B 2.76,1.438 3.219,1.635 0.458,0.198 10 false SST 2.885,3.563 3.344,3.76 0.458,0.198 10 false SST
*A for Type A
*B for Type B


After connecting the following SST to each other, connect them to the horn button assembly.

SST
09082-00802  (09082-10801, 09082-40800)


ii.

for Type A:

Wind 3 wires at least 2 times each around each of the pins.

for Type B:

Wind 3 wires at least 2 times each around each of the claws.

B444337C03
1.583,3.604 1.677,3.354 true 2.406,3.625 2.5,3.375 true 5.104,3.635 5.198,3.385 true 5.948,3.521 6.042,3.271 true 0.323,0.031 0.677,0.24 0.354,0.208 12 false *A 3.906,0.031 4.229,0.229 0.323,0.198 12 false *B 1.469,3.594 1.781,3.75 0.313,0.156 10 false *a 2.313,3.594 2.625,3.75 0.313,0.156 10 false *a 5.021,3.635 5.333,3.792 0.313,0.156 10 false *a 5.813,3.531 6.125,3.688 0.313,0.156 10 false *a
*A for Type A *B for Type B
*a 2 times or more - -


CAUTION:
B401439C01
1.167,1.906 1.302,1.688 true 2.167,1.927 2.302,1.708 true 1.052,1.885 1.365,2.042 0.313,0.156 10 false *a 2.073,1.917 2.385,2.073 0.313,0.156 10 false *a
*a Remove looseness


·

When wrapping the wire harness, make sure there is no looseness.

·

If the wire harness is loosely wrapped, the deployed horn button assembly and tire may fly off and cause serious injuries.




iii.
B444338C03
1.677,0.448 2.104,0.229 false 1.646,2.958 2.073,2.74 false 0.021,0.042 0.448,0.26 0.427,0.219 12 false *A 0.031,2.625 0.385,2.802 0.354,0.177 12 false *B 2.125,0.156 2.438,0.313 0.313,0.156 10 false *a 2.125,2.656 2.438,2.813 0.313,0.156 10 false *a
*A for Type A
*B for Type B
*a Deployment Side


Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

CAUTION:
B399101C01
2.083,1.052 2.5,0.635 true 2.552,0.542 2.865,0.698 0.313,0.156 10 false *a
*a Remove looseness
V100155

Deployment Side


·

Do not install the horn button assembly with the deployment side facing the disc wheel.

·

When securing the horn button assembly, make sure there is no looseness in the wire harness.

·

If the deployment side is facing the disc wheel or the wire harness is loosely wrapped, the deployed horn button assembly and tire may fly off and cause serious injuries.



NOTICE:

The tire and wheel may be damaged by the airbag deployment, so use an unneeded tire and wheel.




d.
B444339C04
2.729,0.625 3.229,0.844 false 2.708,2.99 3.208,3.208 false 0.042,0.135 0.417,0.375 0.375,0.24 12 false *A 0.052,2.5 0.427,2.698 0.375,0.198 12 false *B 2.448,0.51 2.823,0.75 0.375,0.24 10 false SST 2.417,2.875 2.792,3.115 0.375,0.24 10 false SST
*A for Type A
*B for Type B


Install SST.

i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.



ii.
B404071C01
1.198,1.99 1.51,2.146 0.313,0.156 10 false *a
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.



e.
B404072C01
0.5,1.813 0.938,1.594 true 2.729,1.938 2.406,1.729 true 0.323,1.729 0.635,1.885 0.313,0.156 10 false *a 2.823,0.906 2.979,1.104 0.156,0.198 10 false X 0.844,0.729 1,0.927 0.156,0.198 10 true Y 1.073,0.156 1.229,0.354 0.156,0.198 10 false Y 2.781,1.854 3.094,2.01 0.313,0.156 10 false *a
*a Weight


Cover the horn button assembly (using a cardboard box).

i.

Cover the horn button assembly with a cardboard box.


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum cardboard box size:

Must exceed the following dimensions

X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the horn button assembly is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock from the airbag deployment.





f.

Cover the horn button assembly (using tires).

i.

Place at least 3 tires without wheels onto the wheel and tire to which the horn button assembly is tied.

B444340C03
0.563,0.042 0.938,0.25 0.375,0.208 12 false *A 3.885,0.031 4.25,0.26 0.365,0.229 12 false *B 1.99,0.313 2.302,0.469 0.313,0.156 10 false *a 3.042,0.896 3.354,1.052 0.313,0.156 10 false *b 0.896,1.917 1.208,2.073 0.313,0.156 10 false *c 6.063,0.896 6.375,1.052 0.313,0.156 10 false *b 3.917,1.927 4.229,2.083 0.313,0.156 10 false *c 5.021,0.323 5.333,0.479 0.313,0.156 10 false *a
*A for Type A *B for Type B
*a Inner Diameter *b Width
*c Tires (3 or more) - -



ii.

Place a wheel and tire on top.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


NOTICE:
·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

·

Do not place the SST connector under the tire because it could be damaged.




iii.
B105087

Tie the tires together with the 2 wires.



g.

Deploy the airbag.

i.
B404074C01
0.615,1.552 0.427,1.156 false 0.604,3.781 0.417,3.385 false 0.083,0.271 0.396,0.427 0.313,0.156 10 false *A 0.104,2.25 0.417,2.406 0.313,0.156 10 false *B 1.219,1.885 1.531,2.042 0.313,0.156 10 false *a 1.198,4.115 1.51,4.271 0.313,0.156 10 false *a 0.146,1.042 0.604,1.24 0.458,0.198 10 false SST 0.125,3.281 0.583,3.479 0.458,0.198 10 false SST
*A Using a Cardboard Box
*B Using Tires
*a 10 m or more


Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:
B400935

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the horn button assembly.

CAUTION:
·
B396586

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394907

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

If water is applied to the horn button assembly immediately after deployment, burns may occur from the resulting steam.

·
B394909

Always wear safety glasses and gloves when handling a deployed horn button assembly.

·

If the horn button assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394910

Never dispose of a horn button assembly with an undeployed airbag.

·

If an undeployed horn button assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the horn button assembly from the wheel.


ii.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.