Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.07
RM33J0E _51 Engine / Hybrid System _038462 CRUISE CONTROL _0181542 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (for 1GD-FTV)


A340466E23
0.583,0.5 0.979,0.75 0.396,0.25 1.75,0.5 2.146,0.75 0.396,0.25 2.854,0.5 3.25,0.75 0.396,0.25 3.917,0.5 4.313,0.75 0.396,0.25 5,0.5 5.396,0.75 0.396,0.25 6.104,0.5 6.5,0.75 0.396,0.25 0.667,0.552 1.021,0.76 0.354,0.208 10 false C57 1.833,0.552 2.188,0.76 0.354,0.208 10 false C58 2.938,0.552 3.292,0.76 0.354,0.208 10 false C59 4,0.552 4.354,0.76 0.354,0.208 10 false C60 5.083,0.552 5.438,0.76 0.354,0.208 10 false G85 6.188,0.552 6.542,0.76 0.354,0.208 10 false G86

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G45-14 (D) - C60-1 (E1)*1 GR - W-B Clutch switch signal Ignition switch ON, clutch pedal depressed Below 1 V
Ignition switch ON, clutch pedal released 11 to 14 V
G45-14 (D) - C60-1 (E1)*2 GR - W-B D shift position signal Ignition switch ON and shift lever in D, S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in D, S, "+" or "-" Below 1 V
C60-1 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G85-13 (S) - C60-1 (E1)*2 L - W-B S shift position switch signal Ignition switch ON and shift lever in S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in S, "+" or "-" Below 1 V
G85-20 (SFTD) - C60-1 (E1)*2 G - W-B Down-shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "-" (down-shift) Below 1 V
G85-21 (SFTU) - C60-1 (E1)*2 W - W-B Up-shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "+" (up-shift) Below 1 V
G86-1 (BATT) - C60-1 (E1) Y - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G86-12 (ST1-) - C60-1 (E1) GR - W-B Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
0 to 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
G86-13 (STP) - C60-1 (E1) L - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
G86-26 (CCS) - C60-1 (E1) G - W-B Cruise control switch circuit Cruise control main switch off 1 MΩ or higher
Cruise control main switch on Below 2.5 Ω
+RES switch on 235 to 245 Ω
-SET switch on 617 to 643 Ω
CANCEL switch on 1509 to 1571 Ω

*1: for Manual Transmission

*2: for Automatic Transmission



CHECK ECM (for 1KD-FTV)


A254878E06
1.208,0.406 1.615,0.646 0.406,0.24 2.729,0.406 3.135,0.646 0.406,0.24 4.292,0.406 4.698,0.646 0.406,0.24 5.76,0.406 6.167,0.646 0.406,0.24 1.281,0.448 1.594,0.625 0.313,0.177 10 false C55 2.802,0.448 3.115,0.625 0.313,0.177 10 false C56 4.365,0.448 4.677,0.625 0.313,0.177 10 false G83 5.833,0.448 6.146,0.625 0.313,0.177 10 false G84

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C56-7 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G83-2 (BATT) - C56-7 (E1) Y - W-B Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
G83-14 (ST1-) - C56-7 (E1) GR - W-B Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
0 to 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
G83-15 (STP) - C56-7 (E1) L - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
G84-21 (CCS) - C56-7 (E1) G - W-B Cruise control switch circuit Cruise control main switch off 1 MΩ or higher
Cruise control main switch on Below 2.5 Ω
+RES switch on 235 to 245 Ω
-SET switch on 617 to 643 Ω
CANCEL switch on 1509 to 1571 Ω


CHECK TCM (for 1KD-FTV)


C214981E13
1.479,0.208 1.854,0.427 0.375,0.219 3.49,0.208 3.865,0.427 0.375,0.219 5.458,0.208 5.833,0.427 0.375,0.219 1.542,0.25 1.854,0.427 0.313,0.177 10 false C77 3.552,0.25 3.865,0.427 0.313,0.177 10 false G89 5.51,0.25 5.823,0.427 0.313,0.177 10 false G90

HINT:

Each TCM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the TCM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G89-8 (D) - C77-1 (E1) P - W-B D shift position switch signal Ignition switch ON and shift lever in D, S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in S, "+" or "-" Below 1 V
C77-1 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G90-15 (S) - C77-1 (E1) L - W-B S shift position switch signal Ignition switch ON and shift lever in S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in S, "+" or "-" Below 1 V
G90-22 (SFTU) - C77-1 (E1) W - W-B Up-shift position switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "+" position (up-shift) Below 1 V
G90-23 (SFTD) - C77-1 (E1) G - W-B Down-shift position switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "-" (down-shift) Below 1 V


CHECK ECM (for 2TR-FBE)


A352214E10
0.667,0.5 1.083,0.75 0.417,0.25 2.01,0.5 2.427,0.75 0.417,0.25 3.406,0.5 3.823,0.75 0.417,0.25 4.729,0.5 5.146,0.75 0.417,0.25 6.083,0.5 6.5,0.75 0.417,0.25 0.76,0.552 1.219,0.75 0.458,0.198 10 false C52 2.094,0.552 2.552,0.75 0.458,0.198 10 false C53 3.5,0.552 3.958,0.75 0.458,0.198 10 false C54 4.813,0.552 5.271,0.75 0.458,0.198 10 false G45 6.167,0.552 6.625,0.75 0.458,0.198 10 false G46

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G45-18 (D) - C52-3 (E1) P - W-B D shift position signal Ignition switch ON and shift lever in D, S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in D, S, "+" or "-" Below 1 V
C52-3 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω
C54-30 (S) - C52-3 (E1) L - W-B S shift position switch signal Ignition switch ON and shift lever in S, "+" or "-" 11 to 14 V
Ignition switch ON and shift lever not in S, "+" or "-" Below 1 V
C54-27 (SFTD) - C52-3 (E1) G - W-B Down-shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "-" (down-shift) Below 1 V
C54-17 (SFTU) - C52-3 (E1) W - W-B Up-shift switch signal Ignition switch ON and shift lever in S 11 to 14 V
Ignition switch ON and shift lever in "+" (up-shift) Below 1 V
G46-3 (BATT) - C52-3 (E1) Y - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G46-11 (ST1-) - C52-3 (E1) GR - W-B Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
0 to 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
G46-10 (STP) - C52-3 (E1) L - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
G45-22 (CCS) - G45-21 (ECCS) G - BR Cruise control switch circuit Cruise control main switch off 1 MΩ or higher
Cruise control main switch on Below 2.5 Ω
+RES switch on 235 to 245 Ω
-SET switch on 617 to 643 Ω
CANCEL switch on 1509 to 1571 Ω