When using a vise, place aluminum plates between the part and vise.
When using a vise, do not overtighten it.
The following chart describes vehicle types A and B, which are referred to throughout the procedure.
| Vehicle Type A | Vehicle Type B | ||
|---|---|---|---|
| Engine Type | Transmission Type | Engine Type | Transmission Type |
| 2TR-FE | R151 | 1GD-FTV | RC61 |
| 2TR-FBE | AC60 | 1KD-FTV | RC61 |
| - | - | 2GD-FTV | RC60 |
| - | - | 2KD-FTV | RC61 |
| Vehicle Type A | Vehicle Type B | ||
|---|---|---|---|
| Engine Type | Transmission Type | Engine Type | Transmission Type |
| 1KD-FTV | A750F | 1GD-FTV | AC60F |
| 2TR-FE | R151F | RC61F | |
| 2TR-FBE | AC60F | 1KD-FTV | RC61F |
| - | - | 2GD-FTV | RC60F |
| - | - | 2KD-FTV | RC61F |
37230
1.INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY
| *a | Front Side |
| *b | Seal |
| *c | Engraved Arrow |
Install the center No. 1 support bearing assembly to the intermediate shaft.
Carefully insert the part so that the seal does not invert.
Make sure to install the part so that the engraved arrow faces the front of the vehicle.
Install the 2 washers to the intermediate shaft.
| *a | Matchmark |
Align the matchmarks on the center yoke and intermediate shaft, and then install the center yoke to the intermediate shaft.
Install the washer to the intermediate shaft.
Clamp the center yoke in a vise between aluminum plates and press the bearing into position by installing a new lock nut.
Using a chisel and hammer, stake the lock nut.
Fully stake the lock nut along the entire groove.
Do not damage the threads of the intermediate shaft.
2.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY
Use the same procedure for all universal joint spider assemblies.
Apply grease to a new universal joint spider assembly and 2 new spider bearings.
Lithium base chassis grease NLGI No. 2
Do not apply too much grease.
Install the universal joint spider assembly to the flange yoke.
Using SST, install the spider bearing to the universal joint spider assembly.
Using SST, adjust both spider bearings so that the snap ring grooves are as wide as possible and equal in width.
Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.
While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.
| Part No. | Color | Thickness |
|---|---|---|
|
*: For cup with grease nipple. |
||
| 90080-52038 | Blue | 1.638 mm (0.0645 in.) |
| 90080-52039 | Yellow | 1.588 mm (0.0625 in.) |
| 90080-52040 | White | 1.537 mm (0.0605 in.) |
| 90080-52041 | Black | 1.486 mm (0.0585 in.) |
| 90080-52042 | Copper | 1.511 mm (0.0595 in.) |
| 90080-52156* | - | - |
| Part No. | Mark | Thickness |
|---|---|---|
|
*: For cup with grease nipple. |
||
| 90521-A0003* | Black | 1.486 mm (0.0587 in.) |
| 90521-A0005* | Yellow | 1.588 mm (0.0626 in.) |
| 90521-A0006* | Copper | 1.512 mm (0.0594 in.) |
| 90521-A0008 | Black | 1.517 mm (0.0598 in.) |
| 90521-A0010 | Blue | 1.638 mm (0.0646 in.) |
| 90521-A0011 | Black | 1.542 mm (0.0606 in.) |
| 90521-A0013 | Black | 1.618 mm (0.0638 in.) |
| 90521-A0014 | Black | 1.486 mm (0.0587 in.) |
| 90521-A0015 | Copper | 1.512 mm (0.0594 in.) |
| 90521-A0016 | White | 1.556 mm (0.0614 in.) |
While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196in.), select 2 snap rings that have as close to the same thickness as possible.
Use a new snap ring.
Use a snap ring with as close to the same thickness as possible on both ends.
| *a | Hammering Point |
Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and snap ring.
Install the spider bearing on the sleeve side using the procedure described above.
Align the matchmarks on the flange yoke and propeller shaft.
for Pre-Runner:
| *a | Matchmark |
Align the matchmarks on the center yoke and propeller shaft.
| *a | Matchmark |
Align the matchmarks on the sleeve yoke and intermediate shaft.
for 4WD:
| *a | Matchmark |
Align the matchmarks on the center yoke and sleeve yoke.
| *a | Matchmark |
Align the matchmarks on the flange yoke and intermediate shaft.
| *a | Turn |
| *b | Hold |
Using SST, install the 2 spider bearings to the universal joint spider assembly.
Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.
Using SST, adjust both spider bearings so that the front propeller shaft joint spider bearing snap ring grooves are as wide as possible and equal in width.
Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.
While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196 in.), select 2 snap rings that have as close to the same thickness as possible.
Do not reuse the snap rings.
While the installed snap rings should have equal thickness, if the axial play is greater than 0.05 mm (0.00196in.), select 2 snap rings that have as close to the same thickness as possible.
Use a new snap ring.
Use a snap ring with as close to the same thickness as possible on both ends.
| Part No. | Color | Thickness |
|---|---|---|
|
*: For cup with grease nipple. |
||
| 90080-52038 | Blue | 1.638 mm (0.0645 in.) |
| 90080-52039 | Yellow | 1.588 mm (0.0625 in.) |
| 90080-52040 | White | 1.537 mm (0.0605 in.) |
| 90080-52041 | Black | 1.486 mm (0.0585 in.) |
| 90080-52042 | Copper | 1.511 mm (0.0595 in.) |
| 90080-52156* | - | - |
| Part No. | Mark | Thickness |
|---|---|---|
|
*: For cup with grease nipple. |
||
| 90521-A0003* | Black | 1.486 mm (0.0587 in.) |
| 90521-A0005* | Yellow | 1.588 mm (0.0626 in.) |
| 90521-A0006* | Copper | 1.512 mm (0.0594 in.) |
| 90521-A0008 | Black | 1.517 mm (0.0598 in.) |
| 90521-A0010 | Blue | 1.638 mm (0.0646 in.) |
| 90521-A0011 | Black | 1.542 mm (0.0606 in.) |
| 90521-A0013 | Black | 1.618 mm (0.0638 in.) |
| 90521-A0014 | Black | 1.486 mm (0.0587 in.) |
| 90521-A0015 | Copper | 1.512 mm (0.0594 in.) |
| 90521-A0016 | White | 1.556 mm (0.0614 in.) |
| *a | Hammering Point |
Using a hammer, tap the propeller shaft until there is no clearance between the spider bearing outer race and snap ring.
Install the spider bearing on the sleeve side using the procedure described above.
37334C
3.INSTALL REAR SLIDING SHAFT BOOT (for 4WD)
| *1 | Propeller Shaft Boot Clamp |
| *2 | Rear Sliding Shaft Boot |
| *a | Matchmark of Propeller Shaft and Sleeve Yoke |
| *b | Matchmark of Pinching Portion of Propeller Shaft Boot Clamp |
| *c | Pinching Portion |
Temporarily install a new rear sliding shaft boot to the propeller shaft with 2 new clamps.
Coat the splines of the propeller shaft with MP grease.
7.0 to 10.0 g (0.25 to 0.35 oz)
Align the matchmarks on the propeller shaft and sleeve yoke.
Install the sleeve yoke to the propeller shaft and connect the rear sliding shaft boot.
Align the matchmarks on the propeller shaft, sleeve yoke and the pinching portions of the 2 rear propeller shaft boot clamps.
Make sure to align the matchmarks of the propeller shaft boot clamp.
If the pinching portions are installed at different locations than where they were located before disassembly, the rotational balance of the propeller shaft cannot be ensured, which may result in vibrations and noise.
| *a | Turn |
| *b | Hold |
Secure one of the rear propeller shaft boot clamps to the rear sliding shaft boot.
Use the same procedure for each rear propeller shaft boot clamp.
Make sure that the matchmarks of the pinching portion of the rear propeller shaft boot clamp are aligned.
Install SST to the rear propeller shaft boot clamp, and then while pressing the rear sliding shaft boot, slightly tighten the SST bolt.
Correctly set the rear propeller shaft boot clamp to the guide groove.
Do not damage the rear sliding shaft boot.
Tighten SST so that the boot clamp is pinched as shown in the illustration.
3.1 mm (0.122 in.) or less
When tightening SST, make sure the clearance of the rear propeller shaft boot clamp is within the standard clearance.
Do not damage the rear sliding shaft boot.
Remove SST from the rear propeller shaft boot clamp.
Using SST, measure the clearance of the rear propeller shaft boot clamp.
3.1 mm (0.122 in.) or less
If the measured value exceeds the specified value, retighten the rear propeller shaft boot clamp.
4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION
When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.
Fill the grease fittings with grease.
Lithium base chassis grease NLGI No. 2
| *A | for Pre-Runner (Vehicle Type B) | *B | for 4WD |
| *1 | No. 1 Grease Fitting | *2 | No. 2 Grease Fitting |
| *3 | No. 3 Grease Fitting | - | - |
| *a | Vehicle Rear | - | - |
5.INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY