Home › Engine / Hybrid System › 1GD-FTV EMISSION CONTROL › MONOLITHIC CONVERTER(for i-ART) › from 2016.10
RM33J0E _51 Engine / Hybrid System _038423 1GD-FTV EMISSION CONTROL _0290153 MONOLITHIC CONVERTER(for i-ART) A

1GD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER(for i-ART)  INSTALLATION  


PROCEDURE

Hide 25051 1.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket and the exhaust manifold converter sub-assembly to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.


c.
A386539C01
2.49,0.615 2.365,0.427 2.365,0.427 2.229,0.427 true 2.677,1.365 2.677,1.656 true 0.583,1.854 0.854,2.063 0.271,0.208 10 true 90° 2.042,0.323 2.229,0.51 0.188,0.188 10 false *1 2.25,1.208 2.438,1.396 0.188,0.188 10 false *2 2.865,1.208 3.052,1.396 0.188,0.188 10 false *3 2.635,1.677 2.823,1.865 0.188,0.188 10 false *4
*1 Exhaust Pipe Clamp
*2 Exhaust Manifold Converter Sub-assembly
*3 Turbocharger Sub-assembly
*4 Gasket


Install a new exhaust pipe clamp to the exhaust manifold converter sub-assembly with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17118 2.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY

a.

Install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with 2 new nuts and the bolt.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17271 3.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12631A 5.INSTALL ENGINE COVER BRACKET

a.

Install the engine cover bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the cylinder head sub-assembly.


Hide 17578B 6.INSTALL PIPE CLAMP

a.

Install the pipe clamp to the engine cover bracket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY