Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2015.08–2016.01
BM3270E _V1 General _042775 INTRODUCTION _0213647 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


MEASURE VEHICLE HEIGHT


NOTICE:

Before inspecting the wheel alignment, adjust the vehicle height to the specification.


a.
C325025C01
0.083,0.083 0.333,0.25 0.25,0.167 10 false *A 0.083,2.417 0.333,2.583 0.25,0.167 10 false *B 0.26,1.542 0.427,1.708 0.167,0.167 10 false A 0.74,1.667 0.906,1.833 0.167,0.167 10 false B 2.802,3.917 2.969,4.083 0.167,0.167 10 false C 0.208,4 0.375,4.167 0.167,0.167 10 false D
*A for Front
*B for Rear


Press down on the vehicle several times to stabilize the suspension, and measure the vehicle height.

Standard Vehicle Height (for Unloaded Vehicle):
Vehicle Model Front A - B Rear C - D
GUN156R-STFLHQ Tire Size 265/65R17
for Steel Wheel
70 mm (2.76 in.) 72 mm (2.83 in.)
Tire Size 265/65R17
for Aluminum Wheel
70 mm (2.76 in.) 71 mm (2.80 in.)
GUN156R-STFSHQ 70 mm (2.76 in.) 72 mm (2.83 in.)
GUN156R-STFMHQ 71 mm (2.80 in.) 72 mm (2.83 in.)
GUN156R-STTLHQ Tire Size 265/65R17
for Steel Wheel
70 mm (2.76 in.) 72 mm (2.83 in.)
Tire Size 265/65R17
for Aluminum Wheel
70 mm (2.76 in.) 71 mm (2.80 in.)
GUN156R-STTSHQ 70 mm (2.76 in.) 71 mm (2.80 in.)
GUN156R-STTMHQ 71 mm (2.80 in.) 72 mm (2.83 in.)


Measuring point:
A:

Ground clearance of front wheel center

B:

Ground clearance of lower suspension arm No. 2 set bolt center

C:

Ground clearance of rear wheel center

D:

Ground clearance of strut rod set bolt center


If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.

NOTICE:

The standard value shown above is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


a.
C132440C22
2.375,1.094 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.479 false 2.771,0.76 3.021,0.927 0.25,0.167 10 false *b 0.365,0.625 0.604,0.781 0.24,0.156 10 false *a
*a Gauge
*b Alignment Tester


Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.


b.

Inspect the camber, caster and steering axis inclination.

Standard Camber Inclination (for Unloaded Vehicle):
Vehicle Model Camber Inclination
GUN156R-STFLHQ
Right-left error
Tire Size 265/65R17
for Steel Wheel
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17
for Aluminum Wheel
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less
GUN156R-STFSHQ
Right-left error
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less
GUN156R-STFMHQ
Right-left error
Tire Size 265/60R18 0°16' +/-30' (0.27° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less
GUN156R-STTLHQ
Right-left error
Tire Size 265/65R17
for Steel Wheel
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17
for Aluminum Wheel
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less
GUN156R-STTSHQ
Right-left error
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less
GUN156R-STTMHQ
Right-left error
Tire Size 265/60R18 0°16' +/-30' (0.27° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less


Standard Caster Inclination (for Unloaded Vehicle):
Vehicle Model Caster Inclination
GUN156R-STFLHQ
Right-left error
Tire Size 265/65R17
for Steel Wheel
2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17
for Aluminum Wheel
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less
GUN156R-STFSHQ
Right-left error
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less
GUN156R-STFMHQ
Right-left error
Tire Size 265/60R18 2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 2°37' +/-30' (2.62° +/-0.50°)
30' (0.50°) or less
GUN156R-STTLHQ
Right-left error
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less
GUN156R-STTSHQ
Right-left error
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less
GUN156R-STTMHQ
Right-left error
Tire Size 265/60R18 2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 2°37' +/-30' (2.62° +/-0.50°)
30' (0.50°) or less


Standard Steering Axis Inclination (for Unloaded Vehicle):
Vehicle Model Steering Axis Inclination
GUN156R-STFLHQ
Right-left error
Tire Size 265/65R17
for Steel Wheel
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17
for Aluminum Wheel
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less
GUN156R-STFSHQ
Right-left error
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less
GUN156R-STFMHQ
Right-left error
Tire Size 265/60R18 12°13' +/-30' (12.22° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less
GUN156R-STTLHQ
Right-left error
Tire Size 265/65R17
for Steel Wheel
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17
for Aluminum Wheel
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less
GUN156R-STTSHQ
Right-left error
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less
GUN156R-STTMHQ
Right-left error
Tire Size 265/60R18 12°13' +/-30' (12.22° +/-0.50°)
30' (0.50°) or less
Tire Size 265/65R17 12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less


If the camber and caster are not as specified, adjust them.

If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, check the steering knuckle and front wheel for distortion or looseness.



INSPECT TOE-IN


C260042C06
0.698,0.042 0.844,0.24 0.146,0.198 10 A 2.656,0.031 2.802,0.229 0.146,0.198 10 B 1.719,1.563 1.865,1.76 0.146,0.198 10 C 1.677,0.219 1.823,0.417 0.146,0.198 10 D
V100135

Front of the Vehicle


Standard Toe-in (Unloaded Vehicle):
Vehicle Model A + B
C - D
GUN156R-STFLHQ Tire Size 265/65R17
for Steel Wheel
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.)
Tire Size 265/65R17
for Aluminum Wheel
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.)
GUN156R-STFSHQ A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.)
GUN156R-STFMHQ A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.)
GUN156R-STTLHQ Tire Size 265/65R17
for Steel Wheel
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.)
Tire Size 265/65R17
for Aluminum Wheel
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.)
GUN156R-STTSHQ A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.)
GUN156R-STTMHQ A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.)


If the toe-in is not as specified, adjust it at the rack ends.


INSPECT WHEEL ANGLE


a.
C132439C18
0.563,0.146 1.021,0.531 0.458,0.385 10 *a 2.781,0.167 3.198,0.604 0.417,0.438 10 *a 2.427,0.167 2.885,0.594 0.458,0.427 10 *b 0.896,0.146 1.354,0.594 0.458,0.448 10 *b
*a Inside
*b Outside
V100135

Front of the Vehicle


Turn the steering wheel to the left and right full lock positions, and measure the wheel angle.

Standard Wheel Angle (for Unloaded Vehicle):
Inside Wheel Angle Outside Wheel Angle (Reference)
35°00' (33°00' to 36°00')(35.00° (33.00° to 36.00°)) 31°42' (31.70°)


If the angles are not as specified, check and adjust the right and left rack end lengths.