Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY(for Rear Disc Brake)
RM3270E _54 Brake _041695 PARKING BRAKE _0193987 PARKING BRAKE ASSEMBLY(for Rear Disc Brake) A

PARKING BRAKE  PARKING BRAKE ASSEMBLY(for Rear Disc Brake)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47456A 1.INSTALL PARKING BRAKE SHOE GUIDE PLATE

a.

Install the parking brake shoe guide plate with the parking brake shoe guide plate set bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 2.APPLY HIGH-TEMPERATURE GREASE

a.
C321860C01
0,0 0,0 false
V100155

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.


Hide 47447C 3.INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN

a.

for Front Side:

i.

Install the parking brake shoe hold down spring pin.



b.

for Rear Side:

i.

Install the parking brake shoe hold down spring pin.



Hide 47612 4.INSTALL PARKING BRAKE SHOE LEVER LH

a.
C325030C01
0,0 0,0 false
V100155

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the parking brake shoe lever LH which make contact with the No. 1 parking brake shoe assembly LH.


b.
C322549C01
0,0 0,0 false
V113147

Install in this Direction


Install the parking brake shoe lever LH and shim to the No. 1 parking brake shoe assembly LH with a new C-washer as shown in the illustration.


c.
C322550

Using a feeler gauge, measure the clearance between the No. 1 parking brake shoe assembly LH and parking brake shoe lever LH.

Standard clearance:

Less than 0.25 mm (0.00984 in.)


If the clearance is not within the specification, replace the shim with one of a different thickness so that the clearance is within the specification.

Standard Shim:
Thickness Thickness
0.3 mm (0.0118 in.) 0.6 mm (0.0236 in.)
0.4 mm (0.0157 in.) 0.9 mm (0.0354 in.)
0.5 mm (0.0197 in.) -



Hide 46580 5.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

a.
C323602

Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever LH as shown in the illustration.

NOTICE:

Be careful not to damage the No. 3 parking brake cable assembly.



Hide 46550E 6.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

a.

Install the parking brake shoe return tension spring to the No. 1 parking brake shoe assembly LH.


Hide 46590 7.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Connect the parking brake shoe return tension spring to install the No. 2 parking brake shoe assembly LH.


Hide 47406A 8.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C323603C01
0,0 0,0 false
V100155

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the parking brake shoe adjusting screw set shown in the illustration.


b.

Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly LH and No. 2 parking brake shoe assembly LH.


c.
C325019C02
0,0 0,0 false
V113147

Expand in this Direction


Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.


Hide 46580 9.CONNECT NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.
C321848C02
1.135,1.281 0.833,0.583 0.833,0.583 0.583,0.583 true 0.167,0.5 0.5,0.667 0.333,0.167 10 true SST
V113147

Push and Turn in this Direction


Using SST, install the 2 parking brake shoe hold down spring cups and parking brake shoe hold down spring to connect the No. 1 parking brake shoe assembly LH to the backing plate.

SST
09718-00011  


Hide 47613D 10.INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING

a.

Install the parking brake shoe strut compression spring to the parking brake shoe strut LH.


Hide 47614 11.INSTALL PARKING BRAKE SHOE STRUT LH

a.

Install the parking brake shoe strut LH.


b.
C323605C01
0,0 0,0 false
V113147

Push in this Direction


Push the No. 2 parking brake shoe assembly LH towards the rear of the vehicle by hand as shown in the illustration.


Hide 46590 12.CONNECT NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.
C321844C02
2,1.167 2.25,0.583 2.25,0.583 2.5,0.583 true 2.583,0.5 2.917,0.667 0.333,0.167 10 false SST
V113147

Push and Turn in this Direction


Using SST, install the 2 parking brake shoe hold down spring cups and parking brake shoe hold down spring to connect the No. 2 parking brake shoe assembly LH to the backing plate.

SST
09718-00011  


Hide 46550E 13.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING

NOTICE:

Be sure to install each parking brake shoe return tension spring in the correct position and direction.


a.

Install the 2 parking brake shoe return tension springs.

HINT:

First install the front side parking brake shoe return tension spring, and then the rear side parking brake shoe return tension spring.



Hide 14.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C323604C01
1.438,3.417 1.75,3.615 0.313,0.198 10 false *a 0.75,0.25 1.063,0.448 0.313,0.198 10 false *A 4.271,0.25 4.583,0.448 0.313,0.198 10 false *B 5.583,3.417 5.896,3.615 0.313,0.198 10 false *a
*A for LH *B for RH
*a Front - -


NOTICE:

There should be no oil or grease on the friction surfaces of the shoe lining and disc.



Hide 47850 16.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.

Connect the rear disc brake cylinder assembly LH with the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 17.ADJUST REAR DRUM BRAKE SHOE CLEARANCE

Hide 18.CHECK PARKING BRAKE LEVER TRAVEL

Hide 19.INSTALL REAR WHEEL