Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0195472 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E321066E05
1.719,0.563 3.552,0.76 1.833,0.198 10 false from Battery 3.708,0.458 5.542,0.656 1.833,0.198 10 false RADIO 1.438,1.25 3.271,1.448 1.833,0.198 10 false from ACC Relay 1.01,1.917 2.49,2.323 1.479,0.406 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 4.25,1.115 4.875,1.333 0.625,0.219 10 false ACC 3.583,1.781 4.406,1.979 0.823,0.198 10 false IG1 NO.4 5.156,1.938 5.531,2.115 0.375,0.177 10 false G100 5.156,0.583 5.531,0.76 0.375,0.177 10 false G102 5.156,1.26 5.531,1.438 0.375,0.177 10 false G102 5.156,2.51 5.531,2.688 0.375,0.177 10 false G102 5.281,2.292 5.656,2.469 0.375,0.177 10 false 7 5.292,1.708 5.667,1.885 0.375,0.177 10 false 1 5.281,1.052 5.656,1.229 0.375,0.177 10 false 3 5.292,0.354 5.667,0.531 0.375,0.177 10 false 4 5.635,0.604 6.146,0.781 0.51,0.177 10 false +B1 5.625,1.271 6.135,1.448 0.51,0.177 10 false ACC1 5.615,1.917 6.125,2.094 0.51,0.177 10 false IG 5.635,2.521 6.146,2.698 0.51,0.177 10 false GND1 5.25,3.104 6.948,3.438 1.698,0.333 10 false Radio and Display Receiver Assembly 0.333,2.833 3.427,3.052 3.094,0.219 10 false *1: w/ Smart Entry and Start System 0.333,3.198 4.219,3.458 3.885,0.26 10 false *2: w/o Smart Entry and Start System 3.021,1.135 4.146,1.563 1.125,0.427 10 false SFT LOCK-ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E310643C05
1.49,1.854 1.927,2.083 0.438,0.229 1.49,0.333 1.927,0.563 0.438,0.229 0.552,0.979 0.708,0.979 0.708,0.979 0.958,1.219 true 1.219,3.26 1.375,3.26 1.375,3.26 1.625,2.865 true 2.25,2.531 2.469,2.365 2.469,2.365 2.625,2.365 true 2.031,2.49 2.375,2.083 2.375,2.083 2.531,2.083 true 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 1.552,0.375 1.979,0.573 0.427,0.198 10 false G100 1.552,1.896 1.979,2.094 0.427,0.198 10 false G102 2.583,1.969 3.01,2.167 0.427,0.198 10 false ACC1 2.677,2.26 3.104,2.458 0.427,0.198 10 false +B1 0.802,3.156 1.229,3.354 0.427,0.198 10 false GND1 0.333,0.865 0.76,1.063 0.427,0.198 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G102-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G102-4 (+B1) - G102-7 (GND1) Always 11 to 14 V
G102-3 (ACC1) - G102-7 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G100-1 (IG) - G102-7 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR