Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041700 NAVIGATION / MULTI INFO DISPLAY _0197741 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.

It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E319203E07
0.875,0.667 1.583,1.188 0.708,0.521 10 false Telephone Microphone Assembly 1.823,0.573 2.26,0.76 0.438,0.188 10 false MCO+ 1.823,1.365 2.281,1.531 0.458,0.167 10 false MACC 1.833,0.979 2.271,1.167 0.438,0.188 10 false MCO- 2.302,0.573 2.5,0.729 0.198,0.156 10 false 14 2.313,0.99 2.51,1.146 0.198,0.156 10 false 13 2.302,1.365 2.5,1.521 0.198,0.156 10 false 15 0.563,2.521 0.813,2.698 0.25,0.177 10 false Q2 0.573,2.656 1.938,2.854 1.365,0.198 10 false Map Light Assembly 0.229,3.385 0.938,3.563 0.708,0.177 10 false *: Shielded 5.677,0.688 6.063,0.854 0.385,0.167 10 false MIN+ 5.667,1.073 6.052,1.24 0.385,0.167 10 false MIN- 5.677,1.479 6.135,1.646 0.458,0.167 10 false MACC 5.677,1.875 6.135,2.042 0.458,0.167 10 false SGND 5.469,0.594 5.604,0.75 0.135,0.156 10 false 5 5.406,1 5.604,1.156 0.198,0.156 10 false 19 5.427,2.5 5.99,2.667 0.563,0.167 10 false G41 5.438,2.656 6.635,3.021 1.198,0.365 10 false Navigation Receiver Assembly 5.49,1.385 5.625,1.542 0.135,0.156 10 false 4 5.427,1.771 5.625,1.927 0.198,0.156 10 false 18 3.385,2.042 3.531,2.177 0.146,0.135 10 false * 4.563,2.063 4.708,2.198 0.146,0.135 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E280108C17
0.198,0.917 0.583,1.125 0.385,0.208 2.021,1.323 1.25,1.813 1.25,1.813 1.01,1.813 true 2.167,1.333 2.25,1.896 2.25,1.896 2.406,1.896 true 2.156,1.083 2.292,0.292 2.292,0.292 2.448,0.292 true 0,0 0.313,0.156 0.313,0.156 10 false *a 0.271,0.938 0.802,1.146 0.531,0.208 10 false G41 0.604,1.719 0.958,1.917 0.354,0.198 10 false MIN- 2.469,1.802 3.135,1.979 0.667,0.177 10 false SGND 2.542,0.198 3.031,0.365 0.49,0.167 10 false MACC
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-18 (SGND) - Body ground Always Below 1 Ω
G41-19 (MIN-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-4 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the Q2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-5 (MIN+) - Q2-14 (MCO+) Always Below 1 Ω
G41-19 (MIN-) - Q2-13 (MCO-) Always Below 1 Ω
G41-4 (MACC) - Q2-15 (MACC) Always Below 1 Ω
G41-5 (MIN+) - Body ground Always 10 kΩ or higher
G41-19 (MIN-) - Body ground Always 10 kΩ or higher
G41-4 (MACC) - Body ground Always 10 kΩ or higher
G41-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG