Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.08–2016.01
RM3270E _57 Power Source / Network _041704 NETWORKING _0197846 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator upper bracket assembly

·

Harness or connector



WIRING DIAGRAM

B403439E01
0.594,1.698 3.479,1.969 2.885,0.271 10 false Certification ECU (Smart Key ECU Assembly) 0.604,1.51 1.063,1.708 0.458,0.198 10 false G16 4.333,1.708 6.323,2.094 1.99,0.385 10 false Steering Lock Actuator or Upper Bracket Assembly 4.333,1.531 4.792,1.729 0.458,0.198 10 false G19 4.646,0.948 5.104,1.146 0.458,0.198 10 false LIN 2.865,0.938 3.323,1.135 0.458,0.198 10 false LIN 0.74,2.344 2.375,2.583 1.635,0.24 10 false : LIN Communication Line 3.25,0.781 3.406,0.979 0.156,0.198 10 false 5 4.396,0.781 4.552,0.979 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

If the certification ECU (smart key ECU assembly) or steering lock actuator or upper bracket assembly is replaced, refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is output
DTC B2785 is not output



DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

DTC B2785 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G19 steering lock actuator or upper bracket assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-5 (LIN) - G19-5 (LIN) Always Below 1 Ω
G16-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Disconnect the G19 steering lock actuator or upper bracket assembly connector.


b.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

DTC B2785 is output

REPLACE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY