Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM3270E _56 Audio / Visual / Telematics _041701 PARK ASSIST / MONITORING _0197847 TOYOTA PARKING ASSIST-SENSOR SYSTEM D

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  OPERATION CHECK  


MALFUNCTION BUZZER


a.

Turn the ignition switch to ON.


b.

Turn the back sonar or clearance sonar switch assembly on.


c.

Start the sensor check.

HINT:

The sensor check is carried out regardless of vehicle speed and shift position for 5 seconds.



d.

If any of the following conditions occur, the No. 1 clearance warning buzzer will sound.

·

A No. 1 ultrasonic sensor is covered with foreign matter, such as mud or snow.

·

A No. 1 ultrasonic sensor is frozen.

·

A No. 1 ultrasonic sensor is malfunctioning.

·

There is an open circuit between a No. 1 ultrasonic sensor and the clearance warning ECU assembly.


HINT:

When a malfunction is detected, the No. 1 clearance warning buzzer continues to sound as shown in the illustration.


E236274E08
5.813,1.198 7.01,1.51 1.198,0.313 10 false Returns to Normal 3.667,1.073 4.875,1.427 1.208,0.354 10 false *c 2.427,1.104 4.333,1.323 1.906,0.219 10 false *b 2.208,1.74 2.438,1.917 0.229,0.177 10 false On 2.208,1.948 2.5,2.125 0.292,0.177 10 false Off 0.083,0.042 3.375,0.302 3.292,0.26 12 false No. 1 Clearance Warning Buzzer Output: 3.646,0.594 6.167,0.854 2.521,0.26 10 false *a 0.188,2.406 2.708,2.667 2.521,0.26 10 false *a: Approximately 1.5 seconds (1 cycle) 2.729,2.406 4.917,2.667 2.188,0.26 10 false *b: Approximately 0.25 seconds 4.823,2.406 7.01,2.667 2.188,0.26 10 false *c: Approximately 0.75 seconds



DETECTION RANGE MEASUREMENT


NOTICE:

The following measurement and inspection will be performed with the shift lever in a position other than N. Be sure to apply the parking brake and depress the brake pedal firmly to prevent the vehicle from moving.


a.

Turn the ignition switch to ON.


b.

Turn the back sonar or clearance sonar switch assembly on.


c.

Detection range measurement:

i.

Move the shift lever according to the table below.

Measurement Area Shift Lever Position
Rear Center R


ii.

Move a 60 mm (2.36 in.) diameter pole near each sensor to measure its detection range. When measuring the longest-range detection of the rear center sonar, use a wall or equivalent.

NOTICE:

These detection ranges are applicable when positioning the 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The detection range varies depending on the measuring method and type of obstacle (such as walls).


HINT:

Have an assistant move the pole.


Rear Center Sonars Detection Range
E318101C01
5.188,0.292 5.5,0.49 0.313,0.198 10 false *a 5.698,1.521 6.01,1.719 0.313,0.198 10 false *b 4.552,2.552 4.865,2.75 0.313,0.198 10 false *c 4.563,2.938 4.875,3.135 0.313,0.198 10 false *d 5.26,4.635 5.573,4.833 0.313,0.198 10 false *e 4.167,5.5 4.479,5.698 0.313,0.198 10 false *f
*a Wall *b Approximately 1720 mm (67.7 in.)
*c Approximately 1000 mm (39.4 in.) *d Approximately 1500 mm (59.1 in.)
*e Approximately 550 mm (21.6 in.) *f Approximately 200 mm (7.9 in.)




d.

Rear center sonar buzzer operation check

i.

When the No. 1 ultrasonic sensors (rear center) have detected an obstacle, check that the No. 1 clearance warning buzzer sounds.

Operation Condition
Engine Switch Back sonar or clearance sonar switch Assembly Shift Lever Position
ON On R

E320979E01
0.083,0.052 3.167,0.292 3.083,0.24 12 false Clearance Warning Buzzer Operation: 0.521,0.833 2.188,1.083 1.667,0.25 10 false Close-range Detection 2.417,0.625 2.833,0.833 0.417,0.208 10 false On 2.417,1.083 2.792,1.25 0.375,0.167 10 false Off 2.417,1.969 2.792,2.135 0.375,0.167 10 false On 2.417,2.438 2.792,2.604 0.375,0.167 10 false Off 2.417,3.323 2.792,3.49 0.375,0.167 10 false On 2.406,3.802 2.781,3.969 0.375,0.167 10 false Off 2.417,4.667 2.792,4.833 0.375,0.167 10 false On 2.417,5.135 2.792,5.302 0.375,0.167 10 false Off 0.51,2.167 2.177,2.417 1.667,0.25 10 false Medium-range Detection 0.521,3.5 2.104,3.75 1.583,0.25 10 false Long-range Detection 0.521,4.833 2.104,5.083 1.583,0.25 10 false Longest-range Detection 3.042,1.646 3.417,1.813 0.375,0.167 10 false *a 3.292,1.646 3.667,1.813 0.375,0.167 10 false *a 3.167,3.021 3.542,3.188 0.375,0.167 10 false *b 3.646,3.01 4.021,3.177 0.375,0.167 10 false *b 3.188,4.375 3.563,4.542 0.375,0.167 10 false *b 4.406,4.365 4.781,4.531 0.375,0.167 10 false *c 0.208,5.75 2.75,5.917 2.542,0.167 10 false *a: Approximately 0.1 seconds 0.208,6.052 2.75,6.219 2.542,0.167 10 false *b: Approximately 0.2 seconds 0.24,6.333 2.781,6.5 2.542,0.167 10 false *c: Approximately 0.5 seconds

Standard:
Clearance Warning Buzzer Operation
Detection Range During Detection Obstacle
Close-range detection
Within approximately 350 +/- 40 mm (13.8 +/- 1.57 in.)
Buzzer: Sounds continuously 60 mm (2.36 in.) diameter pole
Medium-range detection
From approximately 350 +/- 40 to 450 +/- 50 mm (13.8 +/- 1.57 to 17.7 +/- 1.97 in.)
Buzzer: Sounds intermittently (ON: 0.1 seconds / OFF: 0.1 seconds) 60 mm (2.36 in.) diameter pole
Long-range detection
From approximately 450 +/- 50 to 600 +/- 60 mm (17.7 +/- 1.97 to 23.6 +/- 2.36 in.)
Buzzer: Sounds intermittently (ON: 0.2 seconds / OFF: 0.2 seconds) 60 mm (2.36 in.) diameter pole
Longest-range detection
From approximately 600 +/- 60 to 1500 +/- 150 mm (23.6 +/- 2.36 to 59.1 +/- 5.91 in.)
Buzzer: Sounds intermittently (ON: 0.2 seconds / OFF: 0.5 seconds) Wall


HINT:

Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.