Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM3270E _56 Audio / Visual / Telematics _041701 PARK ASSIST / MONITORING _0197847 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzer using a sound pattern that changes depending on the distance to an obstacle.

WIRING DIAGRAM

E318098E01
5.292,0.75 5.75,0.948 0.458,0.198 10 false BBZ 5.292,1.052 5.75,1.25 0.458,0.198 10 false ER 5.042,0.635 5.5,0.833 0.458,0.198 10 false 1 5.052,0.927 5.51,1.125 0.458,0.198 10 false 2 2.542,0.646 3,0.844 0.458,0.198 10 false 1 2.563,0.927 3.021,1.125 0.458,0.198 10 false 2 2.208,0.635 2.667,0.833 0.458,0.198 10 false Z+ 2.24,0.927 2.698,1.125 0.458,0.198 10 false Z- 1.052,1.417 1.51,1.615 0.458,0.198 10 false G86 1.063,1.573 3.146,1.771 2.083,0.198 10 false No. 1 Clearance Warning Buzzer 4.76,1.719 5.219,1.917 0.458,0.198 10 false G88 4.76,1.875 6.979,2.156 2.219,0.281 10 false Clearance Warning ECU Assembly

PROCEDURE

1.CHECK CLEARANCE WARNING ECU ASSEMBLY (BUZZER CIRCUIT)
a.

Remove the clearance warning ECU assembly with its connectors still connected.

E318089C01
0.563,0.75 1.063,1 0.5,0.25 2.563,0.833 2.729,0.375 2.729,0.375 3.063,0.375 true 3.115,0.281 3.448,0.479 0.333,0.198 10 false ER 0.656,0.781 0.99,0.979 0.333,0.198 10 false G88 0.083,0.083 0.417,0.281 0.333,0.198 10 false *a 3.76,1.323 4.208,1.521 0.448,0.198 10 false GND 3.917,0.083 4.25,0.281 0.333,0.198 10 false *b
*a Component with harness connected
(Clearance Warning ECU Assembly)
*b Waveform



b.

Check the waveform of the clearance warning ECU assembly using an oscilloscope.

Item Content
Terminal No. (Symbol) G88-2 (ER) - Body ground
Tool Setting 2 V/DIV., 200 μsec./DIV.
Condition When sonar detects obstacle (buzzer sounds)

OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the G86 No. 1 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-1 (BBZ) - G86-1 (Z+) Always Below 1 Ω
G88-2 (ER) - G86-2 (Z-) Always Below 1 Ω
G88-1 (BBZ) or G86-1 (Z+) - Body ground Always 10 kΩ or higher
G88-2 (ER) or G86-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL


b.

Check if the same malfunction recurs when the sonar function is operated.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG