This DTC is stored if the navigation receiver assembly judges as a result of its self-check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or short circuit in television camera signal | ·
Harness or connector ·
Rear television camera assembly ·
Navigation receiver assembly |
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Service.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Clear the DTC.
Check for DTCs.
No DTC is output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the G42 navigation receiver assembly connector.
Disconnect the V21 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G42-11 (CA+) - V21-6 (CB+) | Always | Below 1 Ω |
| G42-12 (V+) - V21-3 (CV+) | Always | Below 1 Ω |
| G42-23 (CGND) - V21-5 (CGND) | Always | Below 1 Ω |
| G42-24 (V-) - V21-2 (CV-) | Always | Below 1 Ω |
| G42-11 (CA+) or V21-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| G42-12 (V+) or V21-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| G42-23 (CGND) or V21-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| G42-24 (V-) or V21-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Remove the navigation receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G42-23 (CGND) - Body ground | Always | Below 1 Ω |
| G42-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G42-11 (CA+) - Body ground | Engine switch on (ACC) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the navigation receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
| *a | Component with harness connected
(Navigation Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G42-12 (V+) - G42-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Engine switch on (IG), shift lever in R, camera lens not covered, displaying an image
Waveform 2: Engine switch on (IG), shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear television camera assembly with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTC.
Check for DTCs.
No DTC is output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG