Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › 2015.08–2016.01
RM3270E _59 Vehicle Exterior _041718 MIRROR (EXT) _0197860 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY

a.
B400493C01
2.51,1.01 3.01,0.875 true 0.604,3.167 0.5,2.76 true 0.844,3.177 0.844,2.76 true 2.615,3.167 2.615,2.75 true 2.844,3.167 2.938,2.75 true 0.833,4.021 0.833,3.604 true 1.188,4.01 1.281,3.583 true 1.458,4.021 1.521,3.594 true 1.729,4 1.729,3.583 true 2.042,4.01 1.948,3.594 true 2.354,4.042 2.167,3.594 true 2.688,4.021 2.615,3.594 true 1.094,1.99 1.333,1.25 true 0.083,2.531 0.396,2.688 0.313,0.156 10 false *a 3.073,0.802 3.385,0.958 0.313,0.156 10 false *b 1.031,2.052 1.344,2.208 0.313,0.156 10 false *c 0.385,2.563 0.698,2.76 0.313,0.198 10 false MR 0.708,2.563 1.021,2.76 0.313,0.198 10 false +B2 2.531,2.563 2.844,2.76 0.313,0.198 10 false MF 2.854,2.552 3.167,2.75 0.313,0.198 10 false E2 2.646,4.063 2.958,4.26 0.313,0.198 10 false E 0.792,4.052 1.104,4.25 0.313,0.198 10 false B 1.656,4.063 1.969,4.26 0.313,0.198 10 false HR 1.969,4.063 2.281,4.26 0.313,0.198 10 false VR 2.281,4.063 2.594,4.26 0.313,0.198 10 false M+ 1.375,4.063 1.688,4.26 0.313,0.198 10 false VL 1.104,4.063 1.417,4.26 0.313,0.198 10 false HL
*a Component without harness connected
(Outer Mirror Switch Assembly)
*b Mirror Retract Switch
*c Mirror Select Switch and Mirror Surface Adjust Switch


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (MR) - 1 (E2)
2 (MF) - 4 (+B2)
Extended position Below 1 Ω
5 (MR) - 4 (+B2)
2 (MF) - 1 (E2)
Retracted position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch.

i.

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
15 (B) - 12 (VL)
7 (E) - 9 (M+)
Up Below 1 Ω
Off 10 kΩ or higher
15 (B) - 9 (M+)
7 (E) - 12 (VL)
Down Below 1 Ω
Off 10 kΩ or higher
15 (B) - 13 (HL)
7 (E) - 9 (M+)
Left Below 1 Ω
Off 10 kΩ or higher
15 (B) - 9 (M+)
7 (E) - 13 (HL)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
15 (B) - 10 (VR)
7 (E) - 9 (M+)
Up Below 1 Ω
Off 10 kΩ or higher
15 (B) - 9 (M+)
7 (E) - 10 (VR)
Down Below 1 Ω
Off 10 kΩ or higher
15 (B) - 11 (HR)
7 (E) - 9 (M+)
Left Below 1 Ω
Off 10 kΩ or higher
15 (B) - 9 (M+)
7 (E) - 11 (HR)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.