Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0195472 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio and display receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E328652E01
0.917,1.604 1.375,1.802 0.458,0.198 10 false G49 0.927,1.792 1.385,1.99 0.458,0.198 10 false ECM 1.896,1.031 2.208,1.229 0.313,0.198 10 false 10 1.479,1.073 1.938,1.271 0.458,0.198 10 false SPD 4.906,1.625 6.802,1.885 1.896,0.26 10 false Combination Meter Assembly 4.896,1.427 5.208,1.625 0.313,0.198 10 false G8 5.396,1.042 5.708,1.24 0.313,0.198 10 false +S 5.104,1.042 5.417,1.24 0.313,0.198 10 false 19 0.469,3.083 0.927,3.281 0.458,0.198 10 false G16 0.469,3.271 3.646,3.521 3.177,0.25 10 false Certification ECU (Smart Key ECU Assembly)* 1.469,2.552 1.927,2.75 0.458,0.198 10 false SPD 1.906,2.521 2.063,2.719 0.156,0.198 10 false 7 0.146,5.052 2.792,5.333 2.646,0.281 10 false *: w/ Smart Entry and Start System 5.333,3.104 5.792,3.302 0.458,0.198 10 false G33 5.354,3.313 6.583,3.51 1.229,0.198 10 false Body ECU 5.385,2.563 5.844,2.76 0.458,0.198 10 false SPD 5.167,2.542 5.323,2.74 0.156,0.198 10 false 5 5.021,4.708 5.635,4.906 0.615,0.198 10 false G100 5.042,4.927 6.771,5.323 1.729,0.396 10 false Radio and Display Receiver Assembly 5.385,4.177 5.844,4.375 0.458,0.198 10 false SPD 5.083,4.177 5.396,4.375 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C33
1.479,0.438 1.896,0.656 0.417,0.219 0.656,1.802 0.865,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.479 1.906,0.677 0.313,0.198 10 false G8 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G8-19 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G8-19 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G100 radio and display receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

w/ Smart Entry and Start System:

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G33 body ECU connector.


e.

Disconnect the G49 ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-17 (SPD) - G8-19 (+S) Always Below 1 Ω
G100-17 (SPD) or G8-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR